manualshive.com logo in svg

Sanyo MDF-U730M, Instruction Manual, Page: 29 / 32

Share
Download
Sanyo MDF-U730M Instruction Manual Download Page 29

 28

 

  SPECIFICATIONS

 

 

Name

 

Biomedical Freezer

 

Model

 

MDF-U730M 

External dimensions

 

W770 x D830 x H1955 (mm) 

Internal dimensions

 

W650 x D710 x H1520 (mm) 

Effective capacity

 

690 L 

Exterior

 

Painted steel

 

Interior

 

Painted steel

 

Door Painted 

steel

 

Lock 1 

Insulation 

Rigid polyurethane foamed-in place 

Shelf 

Polyethylene coated wire 

4 pieces 

Size: W626 x D620 (mm)    Max. load: 50 kg/shelf   

Access port 

Diameter 30 mm, 1 port on left side 

1 port on the top of unit 

Compressor 

Hermetic type, 400 W 

Evaporator 

Tube on sheet type 

Condenser 

Wire and tube type   

Refrigerant

 

R-404A 

Temperature controller 

Electronics controller 

Temperature display 

Digital display (between -41 and +1

o

C) 

Temperature sensor 

Thermistor sensor 

Alarm & safety 

High temp. alarm, Low temp. alarm, Power failure alarm, Door alarm, 

Compressor temperature alarm,   

Key lock, Thermal sensor abnormality 

Memory backup 

Nonvolatile memory 

Weight 150 

kg 

Accessories 

1 set of key,   

1 scraper,   

2 large & 2 small nylon clips (for temperature recorder) 

Caster 4 

Leveling foot 

2 

Optional component 

Automatic temperature recorder (MTR-G85)+ Mounting kit (MPR-S7) 

, Automatic temperature recorder (MTR-Mounting kit (MPR-S30) 

Note

:  

Design or specifications will be subject to change without notice. 

The battery for power failure alarm is an article for consumption.    It is recommended that the battery will 

be replaced about every 3 years. 

 
 
 
 
 
 
 
 

Summary of Contents for MDF-U730M

































Reviews:

No comments