background image

 

2

 

   PRECAUTIONS FOR SAFE OPERATION

 

 

It is imperative that the user complies with this manual as it contains 
important safety advice.

 

 

Items and procedures are described so that you can use this unit correctly and safely.   

If the precautions advised are followed, this will prevent possible injury to the user and 

any other person. 

 

Precautions are illustrated in the following way: 

 
 

WARNING

 

 
Failure to observe WARNING signs could result in a hazard to personnel 
possibly resulting in serious injury or death.

 

 
 
 

CAUTION

 

 
Failure to observe CAUTION signs could result in injury to personnel and 
damage to the unit and associated property.

 

 
 

Symbol shows;

 

 

   

 

  this symbol means caution.

 

 

   

 

  this symbol means an action is prohibited.

 

 

   

 

  this symbol means an instruction must be followed.

 

 
Be sure to keep this manual in a place accessible to users of this unit.

 

 

 

< Label on the unit > 

This mark is labeled on the cover in which the electrical components of high voltage are 

enclosed to prevent the electric shock. 

The cover should be removed by a qualified engineer or a service personnel only. 

 

 

 

 

 

Summary of Contents for MDF-1155
























Reviews: