background image

INSTALLATION PARTS

1. Bracket (A)

2. Bracket 

3. 

 bolt

4. Hexagonal 

5. Hexagonal bolt 6. Tapping SCREW

with washer

with washer

with washer

Nut

8. Lock w a s h e r

9. Fiat washer

10. seal

1 1 . Double sided tape

12. DIN 

 cable

M 6

M 5

x 4

x l

x 2

x 4

x 4

13. Power Cable

Yellow

WIRING

1. DIN cable (&pin)

Connect this cable to the 

 LB, 

 LB/FM

Modulator/Ground Isolator or Divider unit.

Power wire (YELLOW)

ect this wire to a terminal which is always energized.

n fuse replacement is necessary, use only a 5 amp fuse.

3. Ground wire (BLACK)

Attach this wire to the chassis of the car. Be sure that the surface
is free of 

paint, 

and is not rusty. If a proper ground connection is

not made, the CD changer may not operate correctly and stray
noise 

may be picked up by the unit.

4. 

Reset button

Be sure to press this button when all wiring is completed or when 

Car battery is replaced.

When a 

malfunction occurs during 

CD play, press the 

button and follow this procedure.

1) The magazine will be automatically ejected 

in about 3 seconds after RESET button 

is pressed.

 A disk being played will still remain on the turntable.

2) Empty the magazine, and insert it again.

The disk on the turntable is automatically housed, and the magazine will be ejected after about 8 seconds.

3) Press the commander reset button after the magazine has been ejected.

Normal operation will then return.

5. Changer selector switch

Do not use this switch if only 1 

CD 

changer is being used.

It 

is used only when 2 

CD 

changers (FXD-C200) are attached.

On how to use it, refer to the operation manual of the divider unit

 

Summary of Contents for FXD-C200










Reviews: