manualshive.com logo in svg

Sanyo CLT-9901, Instruction Manual, Page: 6 / 12

Share
Download
Sanyo CLT-9901 Instruction Manual Download Page 6

Raising the Antenna 

Before using your phone, be sure to raise the base
antenna fully to the vertical position.

Adjusting Ringer/Volume Controls

▼ 

Ringer Tone and Volume

1

While the phone is not in use,  press 

RINGER

.

2

The phone has two ringer tones, each with two
volume levels. Press 

RINGER

again until you hear

the ringer tone and volume level you want.

E5

▼ 

Setting the Handset Earpiece Volume

1

While you are on a call, press 

VOLUME

or

.

2

The phone has three receiver volume levels,

Normal, High, and Loud. Press 

VOLUME

or

repeatedly until you hear the volume level 

you want.

When you hang up, the phone keeps the last
volume setting selected.

▼ 

Direct wall plate mounting

If you do not have a standard wall plate, you can
mount your phone directly to the wall. Before doing
this, consider the following:

• Avoid electrical cables, pipes or other items behind

the mounting location, that could cause a hazard
when inserting screws into the wall.

• Try to mount your phone within 10 –15 feet of a

working phone jack to avoid excessive cord
lengths.

• Make sure the wall material is capable of

supporting the weight of the base and handset.

• Use #10 screws with anchoring devices suitable

for the wall material where the base unit will be
placed.

1

Insert two mounting
screws with a minimum
length of 1-3/8 inches
(35.5 mm) into the wall, 
3-15/16 inches (100 mm)
apart. Allow about 3/16 of
an inch (4.8 mm) between
the wall and screwheads
for mounting the phone.

2

Refer to steps 1 through 9
on page 4 and 5 to mount
the telephone.

TOP

3/16 in.

3-15/16 in.

8

On the base unit, pull the handset retainer out of
the slot. Rotate it clockwise 180 degrees.

9

Flip it over. Slide it back into the slot so that the lip
of the retainer is up and the 

points down. The

retainer holds the handset in place.

COMP

ANDER

NOISE

  R

EDU

CT

ION

PLUS

Handset retainer

When the beltclip is attached onto the
handset, you can hang the handset on
the wall-mounted base with the
keypad facing inside only. 

Setting Up Your Phone

(4.8 mm)

(100 mm)

CLT9902 #4 (SANYO)  8/11/00  4:14 PM  Page 6

Summary of Contents for CLT-9901













Reviews:

No comments