background image

29

11-2. Air conditioner does not operate.

11-2-1.Circuit breaker trips (or fuse blows).

A.  When the circuit breaker is set to ON, it is tripped soon. (Resetting is not possible.)

There is a possibility of ground fault.

Check insulation resistance.

If resistance value is 2M

or less, insulation is defective (“NO”).

B.  Circuit breaker trips in several minutes after turning the air conditioner on.

There is a possibility of short circuit.

Measure insulation
resistance of electrical
parts in outdoor unit.

NO

NO

Set circuit breaker to OFF.

Measure insulation
resistance of electrical
parts in indoor unit.

1

Remove both power supply wires 
and inter-unit wires from terminal 
plate in outdoor unit.
Measure insulation resistance
of outdoor unit.

•  

2

Remove inter-unit wires from 
terminal plate in indoor unit.
Measure insulation resistance
of indoor unit.

•  

•  

•  

Insulation of 
outdoor unit 
is defective.

Insulation of 
indoor unit 
is defective.

Replace with suitable
one (larger capacity).

NO

Check capacity of circuit breaker.

Capacity of circuit breaker is 
suitable.

• Measure resistance of compressor 

motor winding.     (CMA and CMB)

Summary of Contents for 1 852 658 85

















































Reviews: