Sanwa cd732 Instruction Manual Download Page 12 | Manualshive

Page: 12 / 36

background image

Sine wave signal

ACV

0 V

Press the SELECT button

to switch to “

Hz

”.

Line frequency measurement

5-4 Line frequency measurement (Hz)

Hz

99.99 kHz

(

≤

100 Vrms)

9.999 Hz, 99.99 Hz, 999.9 Hz, 9.999 kHz, 99.99 kHz

(Auto range only)

Function Maximum rated input

WARNING

1. Never apply a voltage signal exceeding the maximum rated input value.
2. Do not turn the rotary switch to change the function during measurement.
3. Always keep your fingers behind the finger guards on the test

lead when making a measurement.

Note:

●

The frequency measurement range is from 5 Hz to 99.99 kHz.

The input signal condition is: Sine wave (zero-cross sin signal
waveform) from 5 to 100 Vrms.

●

If the measured frequency contains noise, the measurement

values may become unstable.

●

The bar graph is not displayed with the frequency measurement.

The measurement is possible only with the auto range.

Ranges

– 41 –

«
...
10
11
12
13
14
...
»

Summary of Contents for cd732





































Reviews:

No comments

Related manuals for cd732

Brand: KNOVA Pages: 32

JungleMUX SONET 86447

Brand: GE Pages: 28

Brand: GE Pages: 16

Brand: GE Pages: 24

StoreSafe SDVR-10

Brand: GE Pages: 73

JungleMUX 86445-31

Brand: GE Pages: 95

Brand: GE Pages: 83

86498 ETHER-1000 UNIT

Brand: GE Pages: 174

Brand: Extech Instruments Pages: 14

Brand: Delton Pages: 2

Brand: Delton Pages: 2

Brand: Amprobe Pages: 70

Brand: Amprobe Pages: 68

Brand: Mastech Pages: 40

Brand: Schmidt Pages: 12

PAN Pocketmeter

Brand: PANCONTROL Pages: 186

Brand: Gossen MetraWatt Pages: 18

Brand: Fiber Options Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands