Sanus CFR2100 Series Instruction Manual Download Page 2

2

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the 
damaged item to your dealer; contact Customer Service. Never use damaged parts!

Supplied parts are located inside of the rack. To access the parts, remove the back panel.

Thank you for choosing a Sanus Component Series Rack. The CFR2100 series is designed to support audio/video equipment. 

The total weight capacity for the CFR2100 series:

CFR2115 226.8 kg (500 lb)
CFR2127 340.2 kg (750 lb)
CFR2136 385.5 kg (850 lb)
CFR2144 453.6 kg (1,000 lb)

Each 2U shelf supports up to 22.6 kg (50 lb), and each 1U shelf supports up to 13.6 kg (30 lb). 
Each optional 3U shelf supports up to 36.2 kg (80 lb).

 

CAUTION: 

Avoid potential personal injuries and property damage! 

 

Do not exceed the stated weight capacities.

 

Do not shake, tilt, rock, sit, stand, or climb on your Component Series Rack. Tipping may cause injury or death. 

 

Do not move large racks by yourself; due to weight and height, assistance is required.

 

To avoid instability do not pull out more than one optional drawer or slide out equipment at a time.

 

Before moving, make sure all optional drawers and slide out equipment are secured and door is closed and secured.

 

Use extreme caution when moving a loaded rack! Push, DO NOT pull, loaded rack slowly over a short, smooth, level distance. Avoid 
sudden starts and stops to minimize the strain placed on casters.

 

Do not use this product for any purpose not explicitly specified by manufacturer. 

 

If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product, 
contact manufacturer Customer Service or call a qualified contractor. 

 

Manufacturer is not responsible for damage or injury caused by incorrect assembly or use. 

NOTE:

 Due to continuous product improvement, images shown in this manual may vary from actual product.

IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE MANUAL PRIOR TO USE

Do you have all of the tools needed?

Unpacking

Summary of Contents for CFR2100 Series






















Reviews: