background image

- 15 -

9‑2. Operating method Ⅱ

[In case the Detector is used with no‑voltage contact output・hold function.]

The no-voltage contact output and hold reset function are used to hold the control of the outside

line

marking

alarm lamp etc.

Operations

Cautions

1 Confirm both power source switch

OFF

and hold switch

OFF.

2 Following the previous item 8. INSTALLATION

Connect the same numbered probe after

on page 10, correctly install the main body

confirming the number of the main body.

and the probe.
Insert the cable connector

in the receptacle

of the main body and the receptacle

of the

probe and tighten it by turning the connector
ring.

3 Insert the power source cord

into a receptacle

Connection to a branch receptacle causes

within AC 100V to 240V.

malfunction.

4 Power source switch

ON.

The alarm lamp

will keep on going on under

The power source lamp

will go on and

hold switch

ON condition.

the color changes from red to green.

Hold switch OFF and confirm the alarm lamp

Confirm the buzzer switch

ON.

will go out.

The alarm buzzer

is gone for 2 to 3times,

The Detector can detect nothing while the

and it is possible to detect.

power source lamp

is red color. Confirm

Confirm that the alarm lamp

will go on

the operation for detection after changing the

with buzzer sound.

color from red to green.
The alarm buzzer

does not work when the

buzzer switch

OFF.

5 Turn the sensitivity adjusting dial

to the right

When the sensitivity adjusting dial is at

(clockwise) to set at level [10].

position [0], the Detector can detect nothing.

Summary of Contents for SK-2200


















Reviews: