05
GB
Listening to FM radio
Tuning into FM stations
To tune into FM radio stations, follow these steps:
1.
Fully extend the telescopic antenna located on the rear
of your radio.
2.
Press the
Power button
to turn on the radio.
3.
Select the FM radio mode by repeatedly pressing the
Mode button
.
4.
Rotate the
Tuning knob
clockwise or anti-clockwise
and then press the
Tuning knob
to automatically tune
into an FM station with a higher or lower frequency
respectively. Your radio will stop scanning when it finds
a station of sufficient strength. The display will show the
frequency of the signal which has been found. If RDS
information is available, after a few seconds the display
will show the radio station name.
5.
Rotate the
Tuning knob
to fine-tune the frequency with
steps of 0.05MHz if needed.
6.
Repeat the steps 4 and 5 to tune into other radio
stations.
7.
Rotate the
Volume knob
to set the sound level as
needed.
The FM radio menu
You can enter the FM radio menu by pressing and holding
the
Info / Menu button
while the radio is in the FM radio
mode.
Rotate the
Tuning knob
to select one of the options, then
press the
Tuning knob
to confirm your choice. To exit
menu options, press the
Info / Menu
button.
The radio’s default and recommended settings are
indicated using an asterisk.
The FM radio menu offers the following options:
●
[APS]:
Auto preset system (APS) will automatically
scan and preset the received stations in the order of
signal strength. i.e. the best reception station will be
preset at Preset 1 and so on. Select this option to
initiate the scan.
●
[Audio Settings]:
Select this option to configure if the
radio should only play FM stations in mono. Forcing the
radio to play FM broadcasts in mono can help reduce
noise when listening to FM broadcasts.
To switch back
to Auto (stereo) mode, select the “Auto” option.
●
[Scan Zone]:
Select this option to configure if the
radio should only look for strong signals (“Local”) or
all signals (“Distant”) when using the automatic tuning
feature.
●
[System Settings]:
Select this option to go to the
system settings menu and configure the radio (refer
to the chapter “Using the system settings menu” for
details).
Showing FM information on the display
When listening to a FM radio station that is also
broadcasting RDS data, repeatedly press the
Info / Menu
button
to cycle through the following information on the
radio’s display:
Radio text, Program type, Frequency, Audio type, Signal
strength, Date.
Presetting stations in DAB and FM modes
There are 10 presets each for DAB and FM radio. They
are used the same way for each operating mode.
1.
Press the
Power button
to turn on your radio.
2.
Tune to the required radio station as previously
described.
3.
Press and hold the
Preset button
until the display
shows the “Store Preset” screen.
4.
Rotate the
Tuning knob
to select the desired preset
number.
5.
Press the
Tuning knob
to store the preset station.
“Preset X Stored” will be shown on the display indicating
the station is stored under the selected preset number.
6.
Repeat this procedure as needed for the remaining
presets. If another station has already been stored
under the chosen preset number, that station will be
overwritten.
Recalling a preset in DAB and FM modes
1.
Press the
Power button
to turn on your radio.
2.
Select the DAB or FM radio mode using the
Mode
button.
3.
Press the
Preset button
to display the “Preset Recall”
screen.
4.
Rotate the
Tuning knob
to select a preset number.
5.
Press the
Tuning knob
to confirm your choice. The
radio will tune into the selected preset. The chosen
preset number is also shown on the display.
Listening to music via Bluetooth streaming
You need to pair your Bluetooth device with your
radio
before you can auto-link to play / stream Bluetooth music
through your
radio
. Pairing creates a ‘bond’ so the two
devices can recognize each other.
Pairing and playing your Bluetooth device
for the first time
1.
With your radio switched on, press the
Mode
button
to
select Bluetooth mode. The display will show “Bluetooth
Pairing” and the Bluetooth icon will blink on the display
to indicate that the radio is available for Bluetooth
pairing.
2.
Activate Bluetooth on your device according to the
device’s user manual to link to the radio. Locate the
Bluetooth device list and select the device named
“WR-201D” (With some Smartphone’s that are
equipped with earlier versions than BT2.1 Bluetooth
device, you may need to input the pass code “0000”).
3.
On
ce connected, there will be a confirmation tone
sound. The name of your connected Bluetooth device
will show on the display and the Bluetooth icon will stop
blinking. You can simply select and play any music from
your Bluetooth device.
Summary of Contents for WR-201D
Page 1: ...GB Version 1 WR 201D...
