background image

08

GB

   DBB (Dynamic Bass Boost)

Press and release DBB/● STEP button to activate 

the Deep Bass Boost function to have stronger bass 

sound, display will appear DBB symbol. Press again 

will cancel the DBB.

Note: 

Suggest to activate the DBB when using earphones.

   Software version

The software display cannot be altered and is just for 

your reference.

1. Press and hold DBB/● STEP button when your 

    radio is in power off mode, the screen will show 

    the software version (e.g. A03)

2. Continue pressing and holding the DBB/● STEP 

    and the radio will enter FM/AM step setting.

   FM / AM step setting

3. The screen will show FM tuning step (i.e. FM1 50 

    or 100). Press the Tuning up/down button to choose 

    between 50kHz or 100kHz and then press the Time

    setting button to confirm your setting.

4. After your completion of FM tuning step, the screen 

    will show AM tuning step (i.e. 9  or 10). Press the 

    Tuning up/down button to choose between 9kHz 

    or 10kHz and press the Time setting button to 

    confirm your selection.

Important

Reset of frequency range and tuning step will erase 

all the preset stations stored in your radio.

Summary of Contents for SG-110












Reviews: