SERVICE AND WARRANTY
Your product is not user serviceable.
PLEASE DO NOT TRY TO DISMANTLE THE UNIT.
This product is guaranteed by your supplier for 5 years from the date of manufacture. If it should become defective
please contact your installer or supplier for a replacement unit or visit www.sangamo.co.uk/returns
This product must meet Waste Electronic and Electrical Equipment Regulations (WEEE) for suitable environmental
recycling, recovery and/or disposal. End of life products should be handled in line with local regulations. Alternatively
return end of life product to Sangamo for correct disposal.
CUSTOMER CARE POLICY
As part of Sangamo’s continuous improvement program, the company operates a Customer Care policy. This means we
welcome your comments and complaints, as it can help us to improve our services to you, our customer.
Due to our policy of continuous product improvement and development, the specifications in this guide may be subject
to change without prior notice.
Sangamo Limited
Industrial Estate, Port Glasgow,
Renfrewshire, PA14 5XG
Tel 01475 745131
Fax: 01475 744567
Email: [email protected]
Web: www.sangamo.co.uk
WEE/JH0069TY
143795 Issue C
Programming Notes
The unit will automatically return to normal running
if a period of 30 seconds passes without any buttons
being pressed.
For convenience, to allow for programmes to go past
midnight, the programme day is from 03:00am to
02:50am the next day.
If a programme is required to run from 1.00 am to
8.00 am then 2 programmes must be used because it
is not possible to programme through 2.50 am. (The
programme should be split up into two sections; 3.00
am > 8.00 am and 1.00 am > 2.50 am).
Reset
Press the reset button with a non-metallic pointed
tool to restore the built in programme. As well as
restoring the built in programme, it also resets the
time to 12:00pm and the date to 01/01/2014. Initially
the display shows all segments lit for a few seconds,
but then will show the current configuration. See
SETTING THE TIME section to continue.
As a safety feature after reset the unit will be in OFF
operating mode. Reselect your required operating
mode.
Using Advance
The ADVANCE function allows the user to move
to the next ON or OFF programme for a “one off”
event, without having to change the programme or
operating mode.
Warning: The ADVANCE function is only available
when programme is in AUTO or ALL DAY operating
modes.
To advance Central Heating
Press the
ADV button. This will turn the Central
heating ON if it is in an OFF period and OFF if it is
in an ON period. It will stay in this state until either
ADV button is pressed again, or until a programmed
ON/OFF period commences. The word ADV [5] will
appear in the top left hand corner of the LCD.
Using +HR Boost
Press the
+HR
button to make the desired selection with
one, two or three hours extra heating [6] and cancel
options offered.
Warning:
The +HOUR function is only available when
programme is in AUTO , ALL DAY or OFF operating modes.
If the Central heating operating mode is OFF, then it will
switch on for the extra hours selected. If the Central
heating mode is AUTO or ALL DAY, then during an OFF
period, it will switch on for the extra hours selected.
If during an ON period, then it will temporarily extend
that programme by the number of hours selected, this is
displayed on the right of the LCD display [6].
NOTE:
If the programmer is in the OFF mode and then
+HR
button is pressed (+1 HR, + 2 HR, or + 3 HR) and
the resulting time of the boost overlaps a START / ON time
in the AUTO mode programme memory then the boost will
disengage. If this happens simply press
+HR
button again
and the boost will activate for the time period chosen.
Power Interruption
In the event of a mains supply failure the screen will
go blank but the back-up battery ensures that the
programmer continues to keep the time and retain
your stored programme. When power is restored,
if there has been no change to the rear DIP switch,
the programmer returns to its expected operating
condition.
If the configuration setting on the rear DIP switch
has been altered during the power interruption the
screen will initially show the new configuration. And
the appropriate factory default programme (see
BUILT IN PROGRAMME section) will be installed.
Press
SET button to return to RUN mode.
If you have a problem or require
any further information please
contact us on:
01475 745131
[1] [2]
[3]
[4]
[5]
[6]
The Holiday function allows the user to turn all
channels to the OFF operating mode, for a settable
amount of days from 01-99 days. During this
function a suitcase icon will be displayed.
The number of days will decrease at midnight each
day.
The +HR boost override can be used during a
holiday period.
1.
Press & Hold
DAY button for 4 seconds to enter
the holiday function , d:01 flashes.
2.
Press
+/- button to set the holiday days.
3.
Press
DAY button to activate.
4.
Press & Hold
DAY button for 4 seconds to
cancel a holiday period.
Warning: The Holiday function is only available in
AUTO, ALL DAY or ON operating modes.
Holiday Mode