background image

Installation & Operation Manual                                                                                       Merlin GDP4 

 

 

Rev: 9   03-20

 

4  

   Board Overview  

 

 

1.

 

100-240VAC Mains power Input 

2.

 

100-240VAC Gas Solenoid Valve Power Output.  
 

3.

 

24VDC Gas detector power supply (Zone 1) purchased separately.  

4.

 

24VDC Gas detector power supply (zone 2) purchased separately. 

5.

 

24VDC Gas detector power supply (zone 3) purchased separately. 

6.

 

24VDC Gas detector power supply (zone 4) purchased separately. 

 

7.

 

Remote emergency stop buttons (Volt free) purchased separately).  

8.

 

Heat Sensor: Fusible Links (Volt free) purchased separately 

9.

 

Fire panel connection (Volt free) not included. 

10.

 

BMS output contacts. Normally Open, Common and Normally Closed. 

11.

 

24VDC Sounder/ Strobe alarm - purchased separately 
 

12.

 

Switch - BMS Selection & Auto Reset  

13.

 

Switch - Zone 1, 2, 3 & 4 enable/disable  
 

 

Fuse – 3.15A 

 

 

 

 

 

 

 

 

To avoid electrical shock you 

must always isolate the mains 

supply before opening the 

GDP4 panel cover/s. 

Summary of Contents for Merlin GDP4













Reviews: