manualshive.com logo in svg

Sandpiper S15 Non-Metallic, Service & Operating Manual

Share
Download
Sandpiper S15 Non-Metallic Service & Operating Manual Download Page 27

s15nmdl3sm-REV1207 

                                             

 Model S15 Non-Metallic Page 25 

SAFE AIR

EXHAUST

DISPOSAL

AREA

PUMP INSTALLATION AREA

1"  DIAMETER AIR

EXHAUST PIPING

1"  DIAMETER AIR

EXHAUST PIPING

1"  DIAMETER AIR

EXHAUST PIPING

MUFFLER

LIQUID

LEVEL

SUCTION

LINE

LIQUID

LEVEL

SUCTION

LINE

MUFFLER

MUFFLER

PUMPING HAZARDOUS LIQUIDS

When a diaphragm fails, the pumped 

liquid  or  fumes  enter  the  air  end  of 
the  pump.  Fumes  are  exhausted  into 
the  surrounding  environment.  When 
pumping hazardous or toxic materials, 
the  exhaust  air  must  be  piped  to  an 
appropriate area for safe disposal. See 
illustration #1 at right.

This  pump  can  be  submerged  if 

the  pump  materials  of  construction 
are  compatible  with  the  liquid  being 
pumped. The air exhaust must be piped 
above the liquid level. See illustration #2 
at right. Piping used for the air exhaust  
must  not  be  smaller  than  1"  (2.54 
cm)  diameter.  Reducing  the  pipe 
size  will  restrict  air  flow  and  reduce 
pump performance. When the pumped 
product source is at a higher level than 
the  pump  (flooded  suction  condition), 
pipe  the  exhaust  higher  than  the 
product  source  to  prevent  siphoning 
spills. See illustration #3 at right.

CONVERTING THE PUMP FOR 
PIPING THE EXHAUST AIR

The following steps are necessary to 

convert the pump to pipe the exhaust 
air away from the pump.

Use  a  #8 Torx  or  flat  screwdriver  

to remove the six self-tapping screws  
(item 1-J).

Remove the muffler cap and muffler 

(items 1-D and 1-F). The 1" NPT molded 
threads in the air distribution valve body 
(item 1-B).

Piping  or  hose  may  now  be 

installed.

IMPORTANT  INSTALLATION 

NOTE: The manufacturer recommends 
installing a flexible hose or connection 
between  the  pump  and  any  rigid 
plumbing. This  reduces  stresses  on 
the  molded  plastic  threads  of  the  air 
exhaust  port.  Failure  to  do  so  may 
result in damage to the air distribution 
valve body.

Any  piping  or  hose  connected  to 

the  pump’s  air  exhaust  port  must  be 
physically supported. Failure to support 
these  connections  could  also  result  
in  damage  to  the  air  distribution  
valve body.

CONVERTED EXHAUST ILLUSTRATION

Illustration #1

Illustration #2

Illustration #3

Exhaust Conversion Drawing

Summary of Contents for S15 Non-Metallic



































Reviews:

No comments

Brands by name

Popular brands

Load more brands