background image

Sanden

Heat

Pump

––

Service

Technical

Book

Page

41

of

48

1-3-4 Error History Display Mode 

1) How to Change Mode 

Press and hold down ““UP”” and ““DOWN”” keys together in the Clock Display Mode 

to show the Block out Time Setting Mode.  Press Enter key once to switch to the 
Error History Display Mode.  ““Err0”” will be displayed when the mode is switched 
over.  

 
2) How to Check Error History 

The display repeats ““Err*”” -> ““E***”” -> ““****”” in the Error History Display Mode. 
(““*”” should be a number on the actual panel) 
““*”” in ““Err*”” shows the number of errors.  The latest 10 times of errors can be 

memorized. 

The error number can be changed by pressing ““UP”” or ““DOWN”” key. 
““*”” in ““****”” shows the time that an error has occurred.  For instance, if the display 

shows ““1446””, it means the time that an error occurred is 14:46 (2:46 p.m.).  Date 
of an error occurrence is not memorized. 

 

Following shows the correlation of display and error history: 

[Err0]  Error occurred most recently 
[Err1]  Error occurred earlier than Err0 
  : 
[Err9]  Oldest error memorized in Error History 
““*”” in ““E***”” shows the generated error code. 

 
 

Shown below is the list of the error codes. 

E000  No error generated 
E010  HP Inlet Temperature Thermistor wire break 
E011  HP Inlet Temperature Thermistor short circuit 
E012  HP Outlet Temperature Thermistor wire break 
E013  HP Outlet Temperature Thermistor short circuit 
E014  HP Ambient Temperature Thermistor wire break 
E015  HP Ambient Temperature Thermistor short circuit 
E016  HP Defrost Temperature Thermistor wire break 
E017  HP Defrost Temperature Thermistor short circuit 
E018  HP Discharge Temperature Thermistor wire break 
E019  HP Discharge Temperature Thermistor short circuit 
E020  Tank Thermistor A wire break 
E021  Tank Thermistor A short circuit 
E040  HP water outlet over temperature 1 
E041  HP water outlet over temperature 2 
E042  HP Outlet Temperature Thermistor detection error 
E043  HP discharge over temperature 1 

E044 

HP Discharge Temperature Thermistor detection 
error 

E045  HP Defrost Thermistor detection error 
E047  High pressure side error 
E048  High ambient temperature defrost drive error 
E070  Fan motor locked 
E071  Fan motor revolution error 
E073  Water circulation pump locked 

Summary of Contents for GAU?315EQTA

















































Reviews: