background image

9. LOCKOUT MODE / TAMPER PROTECTION

10. SILENT ENTRY MODE

By activating the silent entry mode, the safe will no 

longer make audible sounds.

Swipe keypad to activate and illuminate keypad.

To turn on silent entry mode, press and hold the (*) 

for 3 seconds. The yellow LED will flash 2 times 

indicating the safe is now in silent entry mode. 

You will not hear any sounds for any functions while 

the safe is in silent entry mode.

To turn the sound back on, press and hold the

(*) for 3 seconds and the yellow LED flashes 2 times 

and will beep indicating you are no longer in silent 

entry mode.

 

 

1. To maximize burglary protection and stability, securing the safe to the floor or 

wall is recommended.

2.

 

3.

 

Always ensure the safe is in an isolated and dry area. Never place the safe in 

direct contact with a wet floor. When installing your  safe on a concrete floor, 

use of a moisture/protective barrier is highly recommended.  Failure to do so, 

or exposing the safe to chemicals or other adverse environments, may void

the warranty.   

 

SA Consumer Products recommends that you store your safe in a closet, office, 

basement, bedroom or any other location that is convenient for you but out of 

direct line of sight from prying eyes. 

11. PROPER PLACEMENT AND MOVING OF SAFE

1. Three consecutive rejected security code entries puts 

the safe in “Basic Lockout” mode. The keypad is 

deactivated for 30 seconds.

2. Six consecutive rejected security code entries results 

in “Severe Lockout” mode. The keypad is deactivated 

for 5 minutes.

Note: During lockout mode, the yellow LED will light up once

every 10 seconds. When lockout mode has ended, the 

green LED will flash 1 time and you will hear 1 beep to 

signify the lockout mode has ended. You will now have 

access to your keypad.

3. After the safe enters basic or severe lockout mode, the tamper indicator will trigger 

to warn you that someone has unsuccessfully attempted to gain access to your safe. 

This tamper indicator will signal immediately after the next successful code is entered. 

The yellow LED will flash 3 times and in addition to a 3 second long beep.

Summary of Contents for Diamond SA-DIA1














Reviews:

Related manuals for Diamond SA-DIA1