San Remo Stoves Maxi Installation And Operating Instructions Manual Download Page 14

 

 

Revised 11-07-11 

 

Lighting the Stove  

 
We recommend that you have two or three small fires before you operate your stove to its 
maximum heat output. This is to allow the paint to cure in steadily and to give a long service life 
of the paint finish. During this curing in process you may notice an unpleasant smell. It is non-
toxic, but for your comfort we would suggest that during this period you leave all doors and 
windows open. 
 
Ensure the Primary and secondary air controls are fully open and place some dry paper or 
firelighters on the grate. Then place a handful of dry kindling on top. Light the fire at the base 
leaving the primary and secondary air open. Allow the fuel to reach a steady glow 
(approximately ten minutes) and then add a little more fuel (approximately two or three small 
logs). Once you have a good fire established across the grate bed, further fuel can be added as 
required and the primary air controls can be shut completely. 
 

Refuelling 

It is best to refuel little and often, rather than in large pieces. When possible refuel the stove 
before the bed has gone too low. Open the primary air controls by about two turns and add the 
fuel. Allow the fuel to burn for a few minutes until the fire is well established before closing the 
primary air once again. This refuelling procedure will ensure that smoke emission is kept to a 
minimum. 

 

 

Shutting Down 

In order to shut down the stove, close the primary air controls, then close the secondary air slider 
by moving the handle all the way to the left. If the controls are left in this position, the fire will 
be starved of air and will go out. If you want to revive the fire it is recommended that the 
primary air controls are open first, and then open the secondary air slider. Please note that the 
stove cannot be shutdown in this manner when the secondary air stop is fitted as this would 
produce smoke. 
 

Warning! - 

The stove will remain 

hot 

for a considerable time after the fire has been 

extinguished. 
 

Notes: 
Warning! - Petroleum coke fuels or household waste must not be burnt on this appliance. 
Should any difficulties arise over fuel quality or suitability, consult your local approved 
coal merchant. 

 

 

 
 
 
 
 
 
 
 

Summary of Contents for Maxi

















Reviews: