WASHING
MACHINE
INSTALLATION GUIDE
3
REMOVING ALL SHIPPING BOLTS (3 OR 4 BOLTS) DEPENDING ON THE MODEL.
Remove all shipping bolts at the
back of washer with supplied
spanner. (Except for WF45H6*,
WF45K* model)
Hold the shipping bolt with your
hand and pull it through the
wide section of the hole. Repeat
for each shipping bolt.
Fill the holes with the supplied
bolt hole covers.
CAUTION: Failure to remove the shipping bolts will cause vibration and noise.
8
LEVEL THE WASHER BY ADJUSTING THE FOUR LEVELING LEGS.
Level the washer by turning the leveling wheel
clockwise or counter clockwise to the required level
with the supplied wrench. (Except for WF45H6*,
WF45K* model)
Check whether washer shakes and level
again, if necessary.
When your washer is leveled, tighten
the locking nuts using the wrench or (-)
flathead screwdriver.
CAUTION: Your washer must be leveled on all four sides. An unlevel washer may cause vibration.
1
PREPARATION.
1. Check the installation location.
□
CHECK
: The floor must be sturdy. (Carpet and soft tile surfaces are not permitted.
2. And move the washer to the installation location.
* When installing the washer on a pedestal, install the pedestal according to its manual.
□
Washer plugged in, power OK
□
No water leakage
□
Water hose connected properly
□
Drain hose connected properly
□
No vibration / noise
□
Washer leveled
□
Shipping bolts removed
INSTALLATION
COMPLETION CHECKLIST
Carpenter’s
level
Pliers
Tape measure
Parts supplied
Tools needed
Hose guide
Anti-slip pads
Water supply hoses
Bolt hole covers
Type1
Type2
Tie strap
(option)
Wrench
(Except for
WF45H6*,WF45K* model)
Flat screwdrilver
5
WATER HOSES INSTALLATION ON WASHER.
Connect one end of the COLD/
HOT water supply hoses to the
each COLD/HOT water supply
intakes at the back of the washer.
Tighten Coupling by hand until
it is snug.
Then tighten two-thirds of a turn
with pliers.
For proper operation, make sure
both Hot & Cold hoses from faucets
are connected to the corresponding
Hot / Cold water inlets on the washer.
CAUTION: Make sure that the HOT & COLD hoses are not switched with each other.
COLD (Left)
Water
HOT (Right)
Water
6
CONNECTING THE DRAIN HOSE.
To keep the drain hose spout
bent, use the supplied plastic
hose guide.
The drain hose must be placed
at a height between 23.6 in
(60cm) and 35.4 in (90cm).
Laundry tub must be no shorter
than 18 in (46 cm) and no longer
than 96 in (245 cm).
Do not insert the drain hose
too far into the stand pipe: 6 - 8
inches, and no more.
Drain hose
Hose guide
Case 1. Wash basin
Case 2. Laundry tub
Case 3. Stand pipe
96” Max
18” Min
Tie strap
Tie strap
Hose
retainer
96” Max
18” Min
8” Max
6” Min
Hose
retainer
7
MOVE THE WASHER TO ITS FINAL LOCATION AND MAKE SURE IT IS LEVELED.
Confirm whether washer is well seated and does not shake. Adjust
leveling legs, if necessary.
Your washer must be leveled on all four sides. Use a carpenter’s level
on all four corners of your washer to ensure it’s level.
4
COLD & HOT WATER HOSES INSTALLATION ON FAUCETS.
Make sure a
Rubber washer
is
inside each coupling on both ends.
Tighten Coupling by hand until
it is snug.
Then tighten two-thirds of a turn
with pliers.
Run water in a bowl or basin to get
rid of any debris inside hose. Check
for HOT and Cold water supply.
Water Supply is separately. (Only for WF36J4*, WF45K*, WF50K* model) To order, please refer to call center number on the back page of your “ User Manual “ .
Rubber
washer
Coupling
Rubber washer
HOT COLD
French on back
Spanish on back
10
Final Test : Water leakage , Vibration & Noise
1. Powering your washing machine.
2. Run a test cycle(Rinse+Spin) with small amount of laundry such as 4~5 Towels.
(1) Check for any leakage at the hose connections.
If water leaks while water is being supplied or drained, check the water connections. (Refer to Step 4,5,6)
(2) Check for vibration and noise.
If the washer rocks and vibrates excessively, level your washer again. (Refer to Step 7,8)
Visits by a Service Engineer to explain functions, maintenance or installation is not covered by warranty.
9
Installing the anti-slip pad
1. Completely clean the bottoms of the adjustable legs and wipe away any dust and oil.
2. Mark the locations of the adjustable front legs of the washing machine where the anti-slip
pads should be installed.
3. Attach the anti-slip pad by tilting or moving the washing machine. When you attach the pad,
remove the plastic film from the pad and attach the sticker side of the pad to the floor so
that the rough side is facing upward. You should not attach the sticker side of the pad to an
adjustable leg.
4. After installing the washing machine and anti-slip pad, check if the adjustable legs are level
again.
Anti-Slip pad is sold separately. (Except for WF36**,592** model) To order,please refer to
call center number on the back page of your "User Manual"
Rough side
Sticker
DC68-02580C-11
2
UNPACKING WASHER.
When unpacking the washing machine,a
collaboration of two persons is required. Do not lay
the machine on its front face when removing the
bottom cushion.
* Models that do not feature handles:
Remove the top cushion from the washing machine
and put the top cushion (or its equivalent) on the
floor. Lay the washing machine on the top cushion
and then remove the bottom cushion.
Make sure to lay the washing machine to its side.
CAUTION: The shipping bolts must stay tightened during this unpacking.
Models with handles
*Models without handles
Parts needed(Sold separately)
* To order, please refer to call center number
on the back page of your "User Manual"
lf applicable
(Except for WF36J4*,WF45K*, WF50K*
model)
Installation Guide-02580C-11_EnCfrMes.indd 1
2016/1/11 17:08:39
