background image

2 _ Safety Instructions

WHILe SeRvICINg

•  Check if the power plug and outlet are damaged, flattened, cut or otherwise degraded.

  If faulty, replace it immediately.

 

Failing to do so may result in electric shock or fire.

•  Completely remove any dust or foreign material from the housing, wiring and connection parts.

  This will prevent a risk of fire due to tracking and electrical hazard..

•  When connecting wires, make sure to connect them using the relevant connectors and check that they are 

completely properly.

  If tape is used instead of the connectors, it may cause fire due to tracking.

•  Make sure to discharge the PBA power terminals before starting the service.

  Failing to do so may result in a high voltage electric shock.

•  When replacing the heater, make sure to fasten the nut after ensuring that it is inserted into the bracket-heater.

  If not inserted into the bracket-heater, it touches the drum and causes noise and electric leakage.

AFTeR SeRvICINg

•  Check the wiring.

  Ensure that no wire touches a rotating part or a sharpened part of the electrical harness.

•  Check for any water leakage.

  Perform a test run for the washing machine using the standard course and check whether there is any water 

leakage through the floor section or the pipes.

•  Do not allow consumers to repair or service any part of the washing machine 

themselves.

  This may result in personal injury and shorten the product lifetime.

•  If it seems that grounding is needed due to water or moisture, make sure to run 

grounding wires.

 

(Check the grounding of the power outlet, and additionally ground it to a metallic water 

pipe.)

  Failing to do so may result in electric shock due to electric leakage.

  [Running a grounding wire]

-  Twist a grounding wire (copper wire) two or three times around the tap.
-  If you connect the grounding wire to a copperplate, bury it 75 cm under the earth in a 

place with a lot of moisture.

  Do not connect the grounding wire to a gas pipe, plastic water pipe or telephone 

wire. There is a risk of electric shock or explosion.

75 cm

Copperplate

WARNINg

WARNINg

Grounding 

terminal

Summary of Contents for WF405ATPASU/A2







































Reviews: