WASHING
MACHINE
Wrench
Bolt hole covers
Type1
Type2
Water supply hoses
Hose guide
Tie strap
(option)
carpenter’s
level
Pilers
Tape measure
Flat screwdrilver
INSTALLATION GUIDE
Parts supplied
Tools needed
2
REMOVING ALL SHIPPING BOLTS.
Remove all shipping bolts
at the back of washer with
supplied spanner.
Hold the shipping bolt
with your hand and pull it
through the wide section of
the hole. Repeat for each
shipping bolt.
Fill the holes with the
supplied bolt hole covers.
CAUTION: Failure to remove the shipping bolts will cause vibration and noise.
7
LEVEL THE WASHER BY ADJUSTING THE FOUR LEVELING LEGS.
Level the washer by turning the leveling
wheel in or out as required by using the
supplied wrench.
Check whether washer shakes
and level again, if necessary.
When your washer is leveled,
tighten the locking nuts using the
wrench or (-) flathead screwdriver.
CAUTION: Your washer must be leveled on all four sides. An unlevel washer may cause vibration.
1
PREPARATION.
1. Check the installation location. □
CHECK
: Solidly constructed floor (Not Carpeting and soft tile surfaces)
2. And move the washer to the installation location.
* When installing the washer on a pedestal, do the installation before next step.
□
Washer plugged in, power OK
□
No water leakage
□
Water hose connected properly
□
Drain hose connected properly
□
No vibration / noise
□
Washer leveled
□
Shipping bolts removed
INSTALLATION
COMPLETION CHECKLIST
4
WATER HOSES INSTALLATION ON WASHER.
Connect one end of the
COLD/HOT water supply
hoses to the each COLD/
HOT water supply intakes
at the back of the washer.
Tighten Coupling by hand
until it is snug.
Then tighten two-thirds of a
turn with pliers.
For proper operation, make
sure both Hot & Cold hoses
from faucets are connected to
the corresponding Hot / Cold
water inlets on the washer.
CAUTION: Make sure that the HOT & COLD hoses are switched with each other.
COLD (Left)
Water
HOT (Right)
Water
5
CONNECTING THE DRAIN HOSE.
To keep the drain hose
spout bent, use the
supplied plastic hose
guide.
The drain hose must be
placed at a height between
23.6 in (60cm) and 35.4 in
(90cm).
Laundry tub must be no
shorter than 18 in (46 cm)
and no longer than 96 in
(245 cm).
Do not insert the drain hose
too far into the stand pipe: 6
- 8 inches, and no more.
Drain hose
Hose guide
Case 1. Wash basin
Case 2. Laundry tub
Case 3. Stand pipe
Tie strap
Tie strap
Hose
retainer
96” Max
18” Min
96” Max
18” Min
8” Max
6” Min
Hose
retainer
6
MOVE THE WASHER TO ITS FINAL LOCATION AND MAKE SURE IT IS LEVELED.
Confirm whether washer is well seated and does not
shake. Adjust leveling legs, if necessary.
Your washer must be leveled on all four sides. Use a
carpenter’s level on all four corners of your washer to
ensure it’s level.
3
COLD & HOT WATER HOSES INSTALLATION ON FAUCETS.
Make sure a
Rubber
washer
is inside each
coupling on both ends.
Tighten Coupling by hand
until it is snug.
Then tighten two-thirds of a
turn with pliers.
Run water in a bowl or
basin to get rid of any debris
inside hose. Check for HOT
and Cold water supply.
Rubber
washer
Coupling
Rubber washer
HOT COLD
French on back
Spanish on back
8
Final Test : Water leakage , Vibration & Noise
1. Powering your washing machine.
2. Run a test cycle(Rinse+Spin) with small amount of laundry such as 4~5 Towels.
(1) Check for any leakage at the hose connections.
If water leaks while water is being supplied or drained, check the water connections. (Refer to Step 3,4,5)
(2) Check for vibration and noise.
If the washer rocks and vibrates excessively, level your washer again. (Refer to Step 6,7)
Visits by a Service Engineer to explain functions, maintenance or installation is
not covered by warranty.
DC68-02580C-0
4
Installation Guide-02580C-03_EnCfrMes.indd 1
2012-07-20 �� 3:28:58
