background image

30_

 cleaning and maintaining your washing machine

CLEANING THE WATER HOSE MESH FILTER

You should clean the water hose mesh filter at least once a year, or when the error message of “

4E

” is 

displayed:

1. 

Turn off the water supply to the washing machine.

2. 

Unscrew the hose from the back of the washing machine. To prevent water from gushing out 
due to the air pressure in the hose, cover the hose with a cloth. 

3. 

Gently pull out the mesh filter from the end of the hose using a pair of pliers and rinse it under 
water until clean. Also clean inside and outside the threaded connector.

4. 

Push the filter back into place.

5. 

Screw the hose back onto the washing machine.

6. 

Make sure the connections are watertight and turn on the tap.

REPAIRING A FROZEN WASHING MACHINE

If the temperature drops below freezing and your washing machine is frozen:

1. 

Unplug the washing machine.

2. 

Pour warm water over the tap to loosen the water supply hose.

3. 

Remove the water supply hose and soak it in warm water.

4. 

Pour warm water into the washing machine drum and let it sit for 10 minutes.

5. 

Reconnect the water supply hose to the water tap and check if the water supply and drain 
are operating normal.

STORING YOUR WASHING MACHINE

If you need to store your washing machine for an extended time, it’s better to drain and disconnect it. 
Washing machines can be damaged if water is left in the hoses and internal components before storage.

1. 

Select the Quick 29’ cycle and add bleach to the bleach compartment. Run your washing 
machine through the cycle without a load.

2. 

Turn the water taps off and disconnect the inlet hoses.

3. 

Unplug your washing machine from the electrical outlet, and leave your washing machine 
door open to allow air to circulate inside the tumbler. 

If your washing machine has been stored in below-freezing temperatures, allow time for any 
leftover water in your washing machine to thaw out before using it.

cleaning and maintaining your 

washing machine

WD8704EJ-02719A_EN.indd   30

2009-10-20   ø¿¿¸ 11:08:17

Summary of Contents for WD8702CJ





































Reviews: