Samsung UPC4082E Installation Manual Download Page 4

E-

4

SELECTION OF INSTALLATION PLACE

Indoor Unit

Outdoor Unit

If there is any unavoidable reason to install the unit at such 

a place, take the following measures against the wind;

1. When installing the unit at a roadside concentrated 

with buildings, install it parallel with the road.

2. Install the unit so that the air outlet faces toward the wall at a

place such as rooftop, which may be subjected to strong wind.

◆ 

The outdoor unit should be installed in accordance with the service space.

◆ 

A place free from the risk of combustible gas leakage.

◆ 

A place which can bear the weight of the unit.

◆ 

A place which can bear the fixing strength of the outdoor unit.

◆ 

Avoid a place subject to oil (including machine oil).

◆ 

Avoid a saline place.

◆ 

Avoid a place subject to sulfide gas (hot spring zone).

(When installing the unit at such special environmental conditions, 

it may cause machine trouble.  When it is unavoidable to use 
such places. It requires special maintenance.)

◆ 

A place where the discharge air and noise of the outdoor unit 
do not disturb the neighborhood.

(Take special care not to cause any inconvenience to your neighbors when installing the unit on the borderline 

with your neighborhood.)

◆ 

A place where strong wind does not head against the air outlet of the outdoor unit.

(If a strong wind heads directly against the air outlet at the time of cool operation, 

a safety device can be operated.)

◆ 

Do not install the outdoor unit at an unstable place such as outer wall of an apartment or building.  
The outdoor unit may fall down, causing severe personal or property damage or loss.

◆ 

Install the unit at a place close to the wall facing the outside as 
it is necessary to perform piping  connection with the outdoor unit.
- It is effective to install the unit at a window side to ensure 

uniform distribution of indoor temperature.

◆ 

Install the unit at a place where there is no obstacle against the 
wind around the air inlet and air outlet.

◆ 

Install the unit horizontally at a stable, rigid place.

(When installing the unit at a place subjected to

oscillation, noise may occur.)

◆ 

Avoid a place near the door which is frequented by people.

◆ 

Avoid a place subject to direct sunlight.

Above 60cm

Above 30cm

Above 50cm

Above 30cm

Above 50cm

Above 30cm

The air inlet faces toward the wall.

The air outlet faces toward the wall.

Space for piping

and wiring

Space for piping

and wiring

Wall

Strong wind

Roof top

Air outlet

Above 

60cm

Above 100cm

Above 50cm

Air outlet

Air inlet

Top view

Side view

Summary of Contents for UPC4082E























Reviews: