background image

 

Ubigate iBG1000 Quick Start Guide 

© SAMSUNG Electronics Co., Ltd. 

III

 

INCIDENCE OF HARM 

If this equipment, the Ubigate iBG1000,

 

causes harm to the telephone 

network, the telephone company will notify you in advance that temporary 
discontinuance of service may be required. But if advance notice isn’t 
practical, the telephone company will notify the customer as soon as 
possible. Also, you will be advised of your right to file a complaint with the 
FCC if you believe it is necessary. 
 

SERVICE CENTER 

If trouble is experienced with the Ubigate iBG1000, please contact your 
local office of SAMSUNG ELECTRONICS, CO., LTD. for repair or 
warranty information. If the trouble is causing harm to the telephone 
network, the telephone company may request that you remove the 
equipment from the network until the problem is resolved. 
 

FIELD REPAIRS 

Only technicians certified on the Ubigate iBG1000, are authorized by 
SAMSUNG ELECTRONICS, CO., LTD. to perform system repairs. 
Certified technicians may replace modular parts of a system to repair or 
diagnose trouble. Defective modular parts can be returned to 
SAMSUNG ELECTRONICS, CO., LTD. for repair. 
 

GENERAL 

Connection to party line service is subject to state tariffs. Contact the 
state public utility commission, public service commission or 
corporation commission for information. 
 

Summary of Contents for Ubigate iBG1000







































Reviews: