Samsung TT17J Series Service Manual Download Page 18

Page: 18 / 70

TT17J*

5-1

5 Troubleshooting

5-1 Parts Level Troubleshooting

Notes:

1. If a picture does not appear, fully rotate the brightness and contrast controls clockwise and reinspect.

2. Check the following circuits.

• No raster appears: Power circuit, Horizontal output circuit.
• High voltage develops but no raster appears: Video output circuits.
• High voltage does not develop: Horizontal output circuits.

5-1-1 No Power Supply

Chirping noise exists?

Check and replace IC601.

Check and replace D601 and FH1

Done.

Yes

Repeating start?

Check and replace D606.

Yes

IC601 Pin 1 waveform is right?

Check and replace D614, IC601,

Q602, and ZD601.

Yes

C622 Voltage is 13 V ± 0.5V?

Check and replace IC201, IC301,

IC401, Q402, and Q404.

Yes

Operate normally?

Replace Main board.

Yes

Verify voltages.

Yes

WAVEFORMS

100 V (IC601, #1)

CH1 P-P = 100 V

CH1 RMS = 350.2 V

Summary of Contents for TT17J Series







































































Search results

Summary of Contents for TT17J Series

Reviews:

Related manuals for TT17J Series

Brands by name

Popular brands

Samsung TT17J Series, Service Manual

Search results

Summary of Contents for TT17J Series

Reviews:

Related manuals for TT17J Series

Brands by name

Popular brands