Installing the Washing Machine
4
SAMSUNG
Washing Machine Owner’s Instructions
In a drain pipe
Samsung recommends you use a 65 cm high vertical pipe; it must be no
shorter than 60 cm and no longer than 90 cm.
The inside of the drain pipe must be wider than the diameter of the drain.
The drain hose can be extended to a length of up to 180 cm. Use an extension
with an internal diameter at least equal to the diameter of the original hose
and a suitable fitting. The hose extension will run along the floor and only the
part near the drainage point will be raised.
Plugging in the machine
For European Users.
You will NOT need to ground the plug of the
washing machine.
For U.S. Users.
You MUST ground the plug of the washing machine.
Check with a licensed electrician before using the machine to make sure it is
properly grounded.
For U.K. Users.
Wiring Instructions
WARNING THIS APPLIANCE MUST BE EARTHED.
This appliance must be earthed. In the event of an
electrical short circuit, earthing reduces the risk of
electric shock providing an escape wire for the
electric current. The appliance is equipped with
a mains lead which includes an earth wire for
connecting to the earth terminal of your mains plug.
The plug must be plugged into a socket that is
properly installed and earthed.
*The wires in this mains lead are coloured in
accordance with the following code:
•Green-and yellow
:Earth
•Blue
:Neutral
•Brown
:Live
• As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings indentifying the terminals
in your plug, proceed as follows.
• Connect the green-and yellow wire to the
terminal in the plug marked with the letter E or
the earth symbol ( ) or coloured green or
green-and-yellow.
• Connect the blue wire to the terminal marked
with the letter N or coloured black.
• Connect the brown wire to the terminal marked
with the letter L or coloured red.
*Consult a qualified electrician or service technician
if in doubt about any of these instructions.
The manufacturer of this washing machine will not accept any
liability for damage to persons or material for non
observance of these requirements.There are no
user+serviceable parts inside the washing machine and if the
mains lead of this appliance is damaged, it must only be
replaced by qualified service personnel approved by the
manufacturer because special tools are required.
Installing the Washing Machine
5
SAMSUNG
Washing Machine Owner’s Instructions
Connecting the water supply hose
The water supply hose must be connected to the washing machine at one end and to the water faucet at
the other. Do not stretch the water supply hose. If the hose is too short and you do not wish to move the
water faucet, replace the hose with a longer, high pressure hose.
To connect the water supply hose:
1.
Connect the cold water supply hose(Blue) fitting with the L-shaped arm to the cold water supply
intake(Blue) on the back of the washing machine and hand tighten.
2.
Connect the other end of the cold water supply hose to your sink’s cold water faucet and tighten it
by hand. If necessary, you can reposition the water supply hose at the washing machine end by
loosening the fitting, rotating the hose, and retightening the fitting.
Option : 1. Connect the hot water supply hose(Red) fitting with the L-shaped arm to the hot water supply
intake(Red) on the back of the washing machine and hand tighten.
2. Connect the other end of the hot water supply hose to your sink’s
hot water faucet and tighten it by hand.
3. If you want to use only cold water, use Y-piece.
Positioning the drain hose
The end of the drain hose may be positioned in three ways:
Over the edge of a sink
The drain hose must be placed at a height of between 60 and 90 cm. To keep the drain hose spout bent,
use the supplied plastic hose guide. Secure the guide to the wall with a hook or to the faucet with a piece
of string to prevent the drain hose from moving.
In a sink drain pipe branch
The drain pipe branch must be above the sink siphon so that the end of the hose is at least 60
cm above the ground.
90 cm
60 cm
GREEN AND
YELLOW
BLUE
BROWN
13 AMP
FUSE
WARNING
Ensure that the plug and power
cord are not damaged before use.
If you have any reason to remove
the moulded plug from this
appliance, immediately remove the
fuse and dispose of the plug.
Do not connect the plug to a mains
socket under any circumstances as
there is a danger of electric shock.
CIRCUITS
Your washing machine should be
operated on a separate circuit from
other appliances. Failure to do this
may cause the circuit breaker to
trip, the fuse to blow.
a
b
a
b
c
1.Remove the adaptor
from the water
supply hose.
2.First,using a "+" type screw driver,
loosen the four screws on the
adaptor. Next,take the adaptor and
turn part(b) following the arrow for
gap about 5mm between them.
3. Connect adaptor to the water tap by
tightening the screws firmly.
Then,turn part (b) following the
arrow and put (a) and (b)together.
5. Connect the other end of the water supply
hose to the inlet water valve at the top of
the washer. Screw the hose clockwise all
the way in.
●
If the water tap is a screw type,assemble a
water supply hose that fits to the tap as
shown.
4. Connect the water supply hose to the
adaptor. Pull down the part (c) of the water
supply hose. When you release part (c) the
hose is automatically connects to the
adaptor making a 'click' sound.
NOTICE
After completing connection,if water leaks from the hose,then repeat the same steps. Use the most conventional type of faucet
for water supply. In case the faucet is square or too big,remove the spacing ring before inserting the faucet into the adaptor.
Connecting the water supply hose (Option)
