background image

10_

 

maintenance

Maintenance

maintenance

 _11

Note: 

  

The Dust Bin may be washed in warmwater with a mild detergent. 

Reassemble and makesure it is completely 

            dry before using again.

To maintain maximum cleaning performance, the following maintenance 

steps must be performed:

1.  Empty the Dust Bin when the dirt reaches the “MAX” 

line on the side.

2.  Cleaning the Grille Cyclone when the Dust Bin 

become clogged.

3.  Check the Pre-Motor Filter at least once a month and 

clean or replace as needed.

4.  Replace the Post-Motor Filter every three to six 

months.

Note: 

 

More frequent filter cleaning or replacing may 

be necessary if you are vacuuming new carpet, 

fine dust, or have allergy concerns. Follow the 

instructions on the following pages to perform 

these simple maintenance steps.

EMpTY DUST bIN

The Dust Bin needs to be emptied when the dirt reaches the “MAX” line on the 

side of it. 

1.  Unplug cleaner from electrical outlet.

2.  To remove the Dust Bin from the vacuum body, push the Dust Bin release button as shown.

3.  Hold dust bin and push down bin release empty button to empty 

    dirt into garbage container as shown.

 WARNING

To reduce the risk of electronic 

shock, turn Power Switch OFF 

and disconnect polarized plug 

from electrical outlet before 

performing maintenance or 

troubleshooting checks.

Tip:

For maximum cleaning 

performance, check and 

clean or replace all filters as 

suggestsd.

cLEANING THE GRILLE

If the suction is weak although the dust bin is empty, open the cover and clean the Grille.

Note: 

  

 Whenever the Grille is clogged, check the pre-motor filter and clear it.

Grille 

Cyclone

Summary of Contents for SU33 SERIES

















Reviews: