background image

Tro u b l e s h o o t i n g

Check this list of possible problems and solutions before bringing your vacuum to a service center.

Problem: Cleaner won’t run

Possible Cause

Possible Solution

·

·

Not firmly plugged in

·

·

Plug unit in firmly

·

·

No voltage in wall plug

·

·

Check fuse or breaker

·

·

Blown fuse or tripped breaker

·

·

Replace fuse or reset breaker

·

·

Filters blocked or dirty

·

·

Clean filters as per manual instructions

Problem : Poor job of dirt pickup

Possible Cause

Possible Solution

·

·

Full or clogged Dirt Cup

·

·

Empty the Dirt Cup and check for blockages.

·

·

Broken or worn belt

·

·

Replace belt.

·

·

Clogged hose or nozzle

·

·

Clean hose or nozzle area.

·

·

Hole in hose

·

·

Replace hose.

·

·

Dirt Cup improperly installed

·

·

Properly install the Dirt Cup

·

·

Incorrect carpet height setting

·

·

Rotate nozzle control knob to lower setting

·

·

Clogs in air flow passage

·

·

Clear clogs/clean filters as per manual instructions

Possible Cause

Possible Solution

·

·

Dirt Cup improperly installed

·

·

Re-install the Dirt Cup.

Problem : Dust escapes the Dirt Cup

Possible Cause

Possible Solution

·

·

Strange sound like rushing air

·

·

Check for clogs in hose, nozzle area and or 

filters, clear or claen any clogs or blockages
as per manual instructions

Problem : Abnormal sound

Possible Cause

Possible Solution

·

·

Incorrect carpet height setting

·

·

Rotate nozzle control knob to lower setting

Problem : Cleaner hard to push

8

DJ68-00294G(0.0)  2007.5.15 4:45 PM  페이지9    in

Summary of Contents for SU-2930 Series













Reviews: