Samsung SSA-S2101 User Manual Download Page 12

Page: 12 / 73

12_

Product Introduction

product introduction

2-PIN Connector

I/O Pins

Signal

Cable Color

Power (+12V)

DC +12V

Red

Earth-grounding

GND (-)

Black

3-PIN Connector

I/O Pins

Signal

Cable Color

RESERVED 1

Pink lwith White Stripes

RESERVED 2

Sky blue with White Stripes

RESERVED 3

Black

6-PIN Connector

I/O Pins

Signal

Cable Color

TTL Output #1

TTL#1, WIK_D_OUT0

Orange with White Stripes

TTL Output #2

TTL#2, WIK_D_OUT1

Brown with White Stripes

Auxiliary Input #1

AUX_IN#1

Green

Auxiliary Input #2

AUX_IN#2

Green with White Stripes

Wiegand Data Input 0

WIK_D_IN0

Pink

Wiegand Data Input 1

WIK_D_IN1

Sky Blue

8-PIN Connector

I/O Pins

Signal

Cable Color

Door RELAY(NC)

NC(1)

Blue with White Stripes

Door RELAY(COM)

COM(1)

Gray with Red Stripes

Door RELAY(NO)

NO(1)

White with Red Stripes

Alarm RELAY(NC)

NC(2)

Purple with White Stripes

Alarm RELAY(COM)

COM(2)

White

Alarm RELAY(NO)

NO(2)

Purple

Exit Button

EXIT

Orange

Door Contact Sensor

CONTACT

Yellow with Red Stripes

4-PIN Connector

I/O Pins

Signal

Cable Color

RESERVED 1

Orange with Red Stripes

RESERVED 2

Orange with Black Stripes

RESERVED 3

Blue

RESERVED 4

Brown

TCP/IP RJ45 Connector

❖

CABLE COLOR SCHEME

Summary of Contents for SSA-S2101










































































Search results

Summary of Contents for SSA-S2101

Reviews:

Related manuals for SSA-S2101

Brands by name

Popular brands

Samsung SSA-S2101, User Manual

Search results

Summary of Contents for SSA-S2101

Reviews:

Related manuals for SSA-S2101

Brands by name

Popular brands