Samsung SpinPoint M9T Page 56 Product Manual Download

Page: 56 / 81

Spinpoint M9T Product Manual REV 1.0

Word

Content

Description

Device initiating interface power management enabled

DMA Setup Auto-Activate optimization enabled

Non-zero buffer offsets in DMA Setup FIS enabled

Reserved (set to 0)

01FFh

Major version number

15-0

ATA-1, ATA-2, ATA-3 and ATA/ATAPI-4, 5, 6, 7

0028h

Minor version number

15-0

ATA/ATAPI-7

X3T13 1532D revision 0

746Bh

Command set supported.

Obsolete

1=NOP command supported

1=READ BUFFER command supported

1=WRITE BUFFER command supported

Obsolete

1=Host Protected Area feature set supported

1=DEVICE RESET command supported

1=SERVICE interrupt supported

1=Release interrupt supported

1=Look-ahead supported

1=Write cache supported

1=supports PACKET Command feature set

1=Power Management feature set supported

1=Removable Media feature set supported

1=Security Mode feature set supported

1=SMART feature set supported

7F69h

Command sets supported.

Shall be set to zero

Shall be set to one

1=FLUSH CACHE Ext supported

1=Mandatory FLUSH CACHE command supported

1=Device Configuration Overlay features supported

1=48 bit address feature supported

Reserved

1=SET MAX Security feature supported

1=Set Address Offset Reserved Area Boot, INCITS TR27:2001

1=SET FEATURES subcommand required to spin-up after power-up.

1=Power up standby feature set supported

1=Removable media status notification feature set supported

1=Advanced Power Management feature set supported

1=CFA feature set supported

1=READ/WRITE DMA QUEUED supported

1=DOWNLOAD MICROCODE command supported

6123h

Command set/feature supported extension.

Shall be set to 0

Shall be set to 1

1=IDLE IMMEDIATE with UNLOAD FEATURE supported

Reserved for technical report

1=URG bit supported for WRITE STREAM DMA EXT and WRITE STREAM

EXT

1=URG bit supported for READ STREAM DMA EXT and READ STREAM

EXT

64-bit World wide name supported

1=Write DMA Queued FUA Ext command supported

1=Write DMA FUA Ext and Write Multiple FUA Ext command supported

1=General purpose logging feature set supported

1=Streaming feature set supported

Summary of Contents for SpinPoint M9T


















































































Search results

Summary of Contents for SpinPoint M9T

Reviews:

Related manuals for SpinPoint M9T

Brands by name

Popular brands

Samsung SpinPoint M9T, Product Manual

Search results

Summary of Contents for SpinPoint M9T

Reviews:

Related manuals for SpinPoint M9T

Brands by name

Popular brands