background image

ENG

CAUTION

1

.  Do not drop objects on the product or apply strong shock to it.  

 

Keep away from a location subject to excessive vibration or magnetic interference.

2

.  Do not install in a location subject to high temperature (over 122°F), low temperature  

 

(below 14°F), or high humidity. Doing so may cause fire or electric shock.

3

.  If you want to relocate the already installed product, be sure to turn off the power  

 

and then move or reinstall it.

4

.  Remove the power plug from the outlet when then there is a lightning. 

 

Neglecting to do so may cause fire or damage to the product.

5

.  Keep out of direct sunlight and heat radiation sources. It may cause fire.

6

.  Install it in a place with good ventilation.

7

.  Avoid aiming the camera directly towards extremely bright objects such as sun,  

 

as this may damage the CCD image sensor.

8

.  Apparatus shall not be exposed to dripping or splashing and no objects filled with  

 

liquids, such as vases, shall be placed on the apparatus.

9

.  The Mains plug is used as a disconnect device and shall stay readily operable at  

 

any time.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following 

two conditions:
1) This device may not cause harmful interference, and
2)  This device must accept any interference received including interference that may 

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to 
part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference 
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of 
this equipment in a residential area is likely to cause harmful interference in which case the user will be required 
to correct the interference at his own expense.

IC Compliance Notice

This Class A digital apparatus meets all requirements of the Canadian interference-Causing Equipment 
Regulations of ICES-003.

01-SCC_B9221_NA-ENG.indd   3

2008-03-10   오후 2:06:45

Summary of Contents for SCC-B9221 - IR Bullet Camera













Reviews: