manualshive.com logo in svg

Samsung S3F84B8, User Manual

Share
Download
Samsung S3F84B8 User Manual Download Page 113

S3F84B8_UM_REV 1.00 

5 INTERRUPT STRUCTURE 

 5-8 

 

5.1.9  SYSTEM MODE REGISTER (SYM) 

The system mode register, SYM (DEH, Set1), is used to enable and disable interrupt processing globally and to 
control fast interrupt processing (see 

Figure 5-5

).  

A reset clears SYM.1 and SYM.0 to “0”. The 3-bit value for fast interrupt level selection, SYM.4–SYM.2, is 
undetermined. 

The instructions EI and DI enable and disable global interrupt processing by modifying the bit 0 value of the SYM 
register. In order to enable interrupt processing, an Enable Interrupt (EI) instruction must be included in the 
initialization routine, which follows a reset operation. Although you can manipulate SYM.0 directly to enable and 
disable interrupts during the normal operation, it is recommended to use the EI and DI instructions for this 
purpose.  

System Mode Register (SYM)

DEH, Set1, R/W

.7

.6

.5

.4

.3

.2

.1

.0

MSB

LSB

Fast interrupt level
selection bits:

0   0   0
0   0   1
0   1   0
0   1   1
1   0   0
1   0   1
1   1   0
1   1   1

IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7

Fast interrupt enable bit:
0 = Disable fast interrupts processing
1 = Enable fast interrupts processing

Not used for the 

S3F84B8

Global interrupt enable bit:
0 = Disable all interrupts processing
1 = Enable all interrupts processing

Always logic "0". 

 

    

Figure 5-5      System Mode Register (SYM) 

Summary of Contents for S3F84B8



































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands