background image

English - 3

IMPORTANT NOTICE

 

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is  

indicated on the pin face of the plug and, if it requires replacing, a fuse approved to BSI1362 of the same rating must be used.
Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must be of the 

same colour as the pin face of the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should 

obtain a suitabl y approved extension lead or consult your dealer for assistance. However, if there is no alternative but to cut off the 

plug, remove the fuse and then safely dispose of the plug.
Do NOT connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord.

IMPORTANT

 

The wires in the mains lead are coloured in accordance with the following code: 

BLUE - NEUTRAL BROWN - LIVE 

As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as  

follows : 

The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK.  

The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.

WARNING:

 

DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED WITH THE 

LETTER E OR BY THE EARTH SYMBOL        , OR COLOURED GREEN OR GREEN AND YELLOW.

Wiring the Mains Power Supply Plug (UK Only)

 

UNITED KINGDOM

 

This Samsung product is warranted for a period of twelve (12) months from the original date of purchase, against  

defective materials and workmanship. In the event that warranty service is required, you should return the product to the retailer 

from whom it was purchased. However, Samsung Authorised Dealers and Authorised Service Centres in other EC Countries will 

comply with the warranty on the terms issued to purchasers in the country concerned. In case of difficulty, details of our Authorised 

Service Centres are available from:

Samsung Electronics U.K. Ltd.

Customer Care Centre

PO Box 143

Edinburgh, EH11 4YB

United Kingdom

Tel: 00 SAMSUNG (664)(UK & Northern Ireland)

Tel: 01 1 100 (EIRE Only)

Fax: +44 045 650 00

Web : www.samsung.com

WARRANTY CONDITIONS

 

1.   The warranty is only valid if, when warranty service is required, the warranty card is fully and properly completed and is 

presented with the original invoice or sales slip or confirmation, and the serial number on the product has not been defaced.

2.  Samsung’s obligations are limited to the repair or, at its discretion, replacement of the product or the defective part.
3.   Warranty repairs must be carried out by Authorised Samsung Dealers or Authorised Service Centres.  

No re-imbursement will be made for repairs carried out by non Samsung Dealers and, any such repair work and damage to the 

products caused by such repair work will not be covered by this warranty.

4.   This product is not considered to be defective in materials nor workmanship by reason that it requires adaptation in order to 

conform to national or local technical or safety standards in force in any Country other than the one for which the product was 

originally designed and manufactured.

Warranty Card

BN68-01936D-Eng.indb   39

2009-02-25   오후 8:43:56

Summary of Contents for PS42B451B2W









































Reviews: