manualshive.com logo in svg

Samsung PS-50C7HR, Service Manual

Share
Download
Samsung PS-50C7HR Service Manual Download Page 81

Operation Instruction & Installation

Samsung Electronics

11-5

1

Remove the screws from the back of the PDP.

2

Use the screw and assemble the plastic hanger.
(Please refer to the following picture.)

1 Please ask the installers to install the wall 

mount bracket.

2 Please be sure to check if the plastic hanger is

completely secured on both the left and right
side after hanging the SET on the wall mount
bracket.

3 Please avoid catching your fingers while

installing and adjusting the angle.

4 Please tightly secure the wall mount bracket to

the wall to avoid injury from a falling SET.

3

Tighten the screws of the plastic hanger (shown
in picture 2) to the back side of the PDP.

4

Remove the Safety Pins. Fasten the 4 plastic 
latches assembled at step ( ) on the back side of
the PDP using the guide holes of the wall mount,
push ( ) and hook ( ) down to secure the PDP on
the wall mount as illustrated. Secure the PDP by
inserting the Safety Pins, not to fall from the wall
mount.

PDP panel

Wall attachment

panel bracket

Wall

11-2-4 Instructions on Securing the SET to the Wall Mount Bracket

Summary of Contents for PS-50C7HR



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands