Samsung PS-42C96HD Service Manual Download Page 51

Page: 51 / 76

Troubleshooting

4-26

Samsung Electronics

■

White Balance - Adjustment

If picture color is wrong, check White Balance condition.

Equipment : CA210, Patten : Toshiba
Adjust W/B in Factory Mode

Sub brightness and R/G/B Offset controls low light region
Sub contrast and R/G/B Gain controls high light region
Source AV : PAL composite, Component : 1280*720/60Hz,

HDMI[DVI] : 1280*720/60Hz

[ Test Pattern : MSPG-945 Series Pattern #16 ]

* Color temperature

1500K +/-500, -6 ~-20 MPCD

* Color coordinate

H/L : 270/280 +/- 2
L/L : 270/280 +/- 3, 2.1 Ft +/-0.05 Ft

( SAMSUNG WHITE BALANCE Adjustment PATTERN with FPD )

■

Conditions for Measurement

1. On the basis of toshiba ABL pattern : High Light level (57 IRE)

- INPUT SIGNAL GENERATOR : MSPG-925LTH
* Mode No 2 : 744X484@60 Hz

No 6 : 1280X720@60 Hz
No 21 : 1024X768@60 Hz

* Pattern No 36 : 16 Color Pattern

No 16 : Toshiba ABL Pattern

2. Optical measuring device : CA210 (FL)

Please use the MSPG-925 LTH generator for model PS-42Q96HD, PS-50Q96HD.

Summary of Contents for PS-42C96HD













































































Search results

Summary of Contents for PS-42C96HD

Reviews:

Related manuals for PS-42C96HD

Brands by name

Popular brands

Samsung PS-42C96HD, Service Manual

Search results

Summary of Contents for PS-42C96HD

Reviews:

Related manuals for PS-42C96HD

Brands by name

Popular brands