Samsung PN50A650T1FXZC Service Manual Download Page 22

Page: 22 / 56

Troubleshooting

4-2

Samsung Electronics

4-1-2 Checkpoints by Error Mode

■ No Power

Symptom

- The LEDs on the front panel do not work when connecting the power cord.

- The SMPS relay does not work when connecting the power cord.

- The unit appears to be dead.

Major

Checklist

The SMPS relay or the LEDs on the front panel does not work when connecting the power cord if the cables

are improperly connected or the Main Board or SMPS is not functioning. In this case, check the following:

- Check the internal cable connection.

- Check the fuses.

- Check the output voltages of the SMPS.

- Replace the Main Board.

Troubleshooting

Procedures

Check that the AC power cord is connected

Connect the AC power cord

①

If LED is set up as being ON when

POWER-ON, check the ligt-on in LED

Is the AC Inlet socket connected?

Check the connection between Fuse FE801

,FB801,FS803 for checking SMPS’s Fuse

Replace Fuse (FE801)

Connect AC Inlet socket

Yes

Check the No. 4 STAND-BY power of

CN801

Yes

Replace the Main Board

Yes

②

③

④

⑤

Replace Fuse

Replace the SMPS

Summary of Contents for PN50A650T1FXZC

























































Search results

Summary of Contents for PN50A650T1FXZC

Reviews:

Related manuals for PN50A650T1FXZC

Brands by name

Popular brands

Samsung PN50A650T1FXZC, Service Manual

Search results

Summary of Contents for PN50A650T1FXZC

Reviews:

Related manuals for PN50A650T1FXZC

Brands by name

Popular brands