Samsung PN15HO Service Manual Download Page 12 | Manualshive

Page: 12 / 82

Samsung PN15HO Service Manual Download Page 12

4-2-1 HIGH VOLTAGE ADJUSTMENT (Only HT/HO)

Signal:

800 x 600 (54 kHz/85 Hz)

Display image: Full White Pattern
Contrast:

Maximum

Brightness:

Maximum

Limit:

25.0 kV ± 0.2 kV

Measure the hight voltage level at the anode cap.
High voltage should be within the limit as above.
If the high voltage needs adjustment use the
following procedure.

PROCEDURE

1. Turn the power off and disconnect the AC line

cord from the power source.

2. Turn the power on after connecting high

voltage Probe.

3. Using the jig, adjust the high voltage to the

specification.

* High Voltage Adjustment PROCEDURE using Softjig

①

Select matching model name in “Model” field.

➁

Select “ @7: Zero Beam” in menu after
selecting “Extra 1”

➂

Adjust high voltage using control bar after
selecting “HV MIN”

➃

Turn the power off/on after adjustment
finished.

➄

Check the high voltage has been fixed with
adjusted value after reselecting “@7: Zero Beam”.

4-2-2 CENTER RASTER

Adjust VR401 so that the back raster comes to the
center when you apply each basic mode.

4-2-3 Centering

Centering means to position the center point of
the display in the middle of the display area.
Horizontal size and position and vertical size and
position control the centering of the display.

Adjust the horizontal size and vertical size to their
optimal settings: 267 mm (H) x 200 mm.

Adjust the horizontal position and vertical
position to

≤

4.0 mm of the center point of the

screen.

|A – B|

≤

4.0 mm.

|C – D|

≤

4.0 mm.

Figure 4-3. Centering

4-2-3 (a-1) HORIZONTAL SIZE ADJUSTMENT

CONDITIONS

Scanning frequency:

54 kHz/85 Hz (VT/VO)
68 kHz/85 Hz (HT/HO)

Display image:

Crosshatch pattern

Brightness:

Maximum

Contrast:

Maximum

Use control bar after selecting “SIZE B+” in left
menu to adjust the horizontal size of the display
pattern to 255 mm . (Tolerance: ± 1 mm.)

4-2-3 (a-2) HORIZONTAL SIZE ADJUSTMENT

Use control bar after selecting “H-SIZE” in left
menu to adjust the horizontal size of the display
pattern to 267 mm . (Tolerance: ± 3 mm.)

4-2-3 (b) VERTICAL SIZE ADJUSTMENT

CONDITIONS

Scanning frequency:

54 kHz/85 Hz

Display image:

Crosshatch pattern

Brightness:

Maximum

Contrast:

Maximum

Use control bar after selecting “V-SIZE” in left
menu to adjust the vertical size of the display
pattern to 200 mm. (Tolerance: ± 3 mm.)

4 Alignment and Adjustments

PN15VT/VO
PN15HT/HO

4-3

4-2 Display Control Adjustments

C

A

DISPLAY AREA

EDGE OF BEZEL

B

D

«
...
10
11
12
13
14
...
»

Summary of Contents for PN15HO



















































































Reviews:

No comments