manualshive.com logo in svg

Samsung PCJ522RX/XAA, Service Manual

Share
Download
Samsung PCJ522RX/XAA Service Manual Download Page 18

Alignment and Adjustments

4-4

Samsung Electronics

4-3 Beam Alignment

PRECAUTION

1.  Input a crosshatch and dot pattern.

2.  Select the “STANDARD” video mode.

3.  Warm up the TV for at least 10 minutes.

4.  Connect an audio oscillator to the pin jig between GT401~GT402 (located on the deflection

PCB) and GND.

5.  Determine the ZERO-magnet area (using the beam-alignment CY)

6.  Check the squarewave at the point where the focus is misaligned (Use an audio oscillator).

ADJUSTMENT

1.  Cover the Red and Blue lenses.

2.  Adjust the Green lens as shown in the figures below

3.  Adjust the G-Focus  until any light around the core disappears.

4.  Cover the Green and Blue lenses.

5.  Adjust the Red lens using the same method as with the Green lens.

6.  Note: The Blue lens is not adjusted because its focus varies little (VM-coil is installed).

7.  After the adjustments are completed, disconnect the jig pin connector. 

(Creation of CPM Zero Magnet)

(Creation of the 2-pole/4-pole zero magnets)

G-FOCUS

CORE

(Varying G-Focus Pack)

Varying the 2-pole of VM

(Positioning the Core in the Center)

 Varying the 4-pole of VM 

CORE

G-FOCUS

(When VM 2-Pole Adjustment is completed)

(Adjust until the light around 

the core becomes a circle)

Summary of Contents for PCJ522RX/XAA










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands