Samsung ND200HHXEA Installation Manual Download Page 25

E-

25

Troubleshooting

  If an error occurs during the operation, an LED flickers and the operation is stopped except the LED.

  If you re-operate the air conditioner, it operates normally at first, then detect an error again.

Detection of errors

LED Display on the receiver & display unit

LED Display

 

On      Flickering      Off

  If you turn off the air conditioner when the LED is flickering, the LED is also turned off.

  If you re-operate the air conditioner, it operates normally at first, then detect an error again.

Abnormal conditions

Indicators

Operating

Concealed Type

Green

Red

Standard Type

Power reset
Error of temperature sensor in indoor unit  

(OPEN/SHORT)

Displayed on appropriate 

indoor unit which is operating

Error of heat exchanger sensor in indoor unit 

Error of heat exchanger OUT sensor in  

indoor unit 

Error of outlet temperature sensor in  

indoor unit  

(OPEN/SHORT): For heat pump models only

Displayed on appropriate 

indoor unit which is operating

Error of outdoor temperature sensor 

Error of COND sensor 

Error of DISCHARGE sensor

Displayed on appropriate 

indoor unit which is operating 

Displayed on outdoor unit

1.  No communication for 2 minutes between 

indoor unit and outdoor unit (communica-

tion error for more than 2 minutes)

2.  Indoor unit receiving the communication 

error from outdoor unit

3. Outdoor unit tracking 3 minute error
4.  When sending the communication error 

from outdoor unit the mismatching of the  

communication numbers and installed  

numbers after completion of tracking.  

(communication error for more than  

2 minutes)

1.  Error of indoor unit: 

Displayed on the indoor unit 

regardless of operation

2.  Error of outdoor unit: 

Displayed on the indoor unit 

which is operating

AVXDU@@_IM_E_33764A-1_110621.indd   25

2011-06-23   오전 10:14:36

Summary of Contents for ND200HHXEA





























Reviews: