Samsung MM-18 Service Manual Download Page 7

Page: 7 / 61

2. Product Specfications

Samsung Electronics

2-1

General

Amp

Cassette

Tuner

Compact Disc

MW
(AM)

(option)

Power source

Power consumption

Dimensions (mm)

Power output (Front)

Total harmonic distortion

Frequency range

Signal to noise ratio

Channel separation

Frequency range

Usable sensitivity

Signal to noise ratio

IF rejection ratio

Total harmonic distoration

Separation (Stereo)

Frequency range

Usable sensitivity

Signal to noise ratio

IF rejection ratio

Total harmonic distortion

Frequency range

WOW FLUTTER

Erasing effect

Signal to noise ratio

Total harmonic distortion

Frequency response

Signal to noise ratio

Channel separation

Total harmonic distortion

Audio Output

125Hz ~ 10KHz

0.35%

55 dB

40 dB

2.5%

20Hz ~ 20KHz(±1dB)

90 dB(1kHz)

75 dB(1kHz)

0.1% (1KHz)

1V (1kHz 0dB)

Frequency range

Usable sensitivity

Signal to noise ratio

146 ~ 290KHz

63 dB

31 dB

87.5 ~ 108MHz

6 dB

50 dB

60 dB

0.8%

25 dB

522 ~ 1611KHz (Option)

56 dB

38 dB

45 dB

5W / Ch (4 ohm)

0.5% (1kHz)

50Hz ~ 17kHz

68 dB

38 dB

AC 115/230V 50/60Hz(Option)

30W

160(W) x 255(H) x 264(D)

Specifications are subject to change without notice.

mm18(10) 3/23/98 2:48 PM Page 1

Summary of Contents for MM-18






























































Search results

Summary of Contents for MM-18

Reviews:

Related manuals for MM-18

Brands by name

Popular brands

Samsung MM-18, Service Manual

Search results

Summary of Contents for MM-18

Reviews:

Related manuals for MM-18

Brands by name

Popular brands