manualshive.com logo in svg

Samsung ML-1610XBH, Service Manual, Page: 70 / 131

Share
Download
Samsung ML-1610XBH Service Manual Download Page 70

Disassembly and Reassembly

Samsung Electronics

Service Manual

5-9

3.Separate the fuser by unscrewing 4 screws on the

frame.

(Screw x 4:Gold_M3,6003-000269)

4.After removing the Lamp Cover L/R, separate the

Fuser Dummy cover.

5.Separate the Exit roller F/Down and the exit gear

(DRV17)by turning the left/right holder connected to
the exit roller F/Down to the arrow direction.At this
time,roller_main,roller_FR, F/Down Holder,and
spring are separated with theses.

6.Remove the thermo cap by releasing 2 screws as

shown as below.

(Screw x 2:Black_M3,6003-000282)

Note : Under the condition that the fuser is connected to the frame,the exit roller F/Down can be separat-

ed.However,be careful that the Roller_Main,the Roller_FR,and F/Down Holder could get into the inner
frame due to the spring’ action.

Fuser

Exit Roller F/Down

Holder

Exit Gear

F/Down Holder

Roller_FR

Roller_Main

Thermo Cap

Fuser Dummy Cover

Lamp Cover_R

Lamp Cover_L

Summary of Contents for ML-1610XBH




































































































































Reviews:

No comments