background image

10

Indoor unit installation

It is recommended to install the refnet joint before installing the indoor unit.

1.  Place the pattern sheet on the ceiling at the spot where you want to install 

the indoor unit.

Since the diagram is made of paper, it may shrink or stretch slightly due 
to temperature or humidity. For this reason, before drilling the holes 
maintain the correct dimensions between the markings; refer to pages 
8~9.

2.  Insert bolt anchors, use existing ceiling supports or construct a suitable 

support as shown in figure.

3.  Install the suspension bolts depending on the ceiling type.

•   Ensure that the ceiling is strong enough to support the weight of the 

indoor unit.  Before hanging the unit, test the strength of each attached 
suspension bolt.

•  If the length of suspension bolt is more than 1.5m(59.06 inch), it is 

required to prevent vibration.

•  If this is not possible, create an opening on the false ceiling in order to 

be able to use it to perform the required operations on the indoor unit.

4.  Screw eight nuts to the suspension bolts making space for hanging the 

indoor unit.

You must install more than four suspension bolt when installing the 

indoor unit.

5.  Check the level of the indoor unit by using a leveler or a vinyl tube filled with 

water.

 - A tilt of the indoor unit may cause malfunction of a built-in float switch and 

water leaks.

6.  Adjust the height of the indoor unit by using the gauge of dimensions.

 - You should adjust the gauge of dimensions and the pattern sheet to fit the 

cutting dimensions of ceiling.

 - Make sure that the indoor unit is installed at a level if the indoor unit slants 

too much, there can be water leaks.

Ceiling

Gauge of Dimensions

Air 

inlet

Air 

outlet

15

m

m

(0

.5

9"

)

15

m

m

(0

.5

9"

)

MH

✴✴✴

FSBA

 

Ceiling

Gauge of 

Dimensions

17mm(0.67")

20mm(0.79")

Indoor unit

MH

✴✴✴

FSBA

7.  Tighten the upper part nuts.
8.  Remove the gauge of dimensions after installing the indoor unit.

Ceiling support

Concrete

Suspension bolt(3/8" or M10)

Hole in anchor
Hole in plug

Insert

Not supplied

Washer 

(supplied)

Rubber

Fasten the nut

Vinyl tube

Level

NOTE

CAUTION

CAUTION

FJM IDU-PH_Cassette type_IM_31595A-04_EN.indd   10

2015-11-16   오후 4:52:21

Summary of Contents for MH FMBA Series



























Reviews: