Samsung ME16H702SEB Installation Instructions Manual Download Page 3

3

General information

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded 

outlet. The installer must perform a ground 

continuity check on the power outlet box before 

beginning the installation to insure that the 

outlet box is properly grounded. If not properly 

grounded, or if the outlet box does not meet 

electrical requirements noted (under ELECTRICAL 

REQUIREMENTS), a qualified electrician should be 

employed to correct any deficiencies.

CAUTION: For personal 

safety, remove house 

fuse or open circuit 

breaker before 

beginning installation 

to avoid severe or fatal 

shock injury.

CAUTION: For personal safety, the mounting 

surface must be capable of supporting the 

cabinet load, in addition to the added weight 

of this 59 pound product, plus additional oven 

loads of up to 50 pounds or a total weight of 

109 pounds.

CAUTION: For personal safety, this product 

cannot be installed in cabinet arrangements 

such as an island or a peninsula. It must be 

mounted to BOTH a top cabinet AND a wall.

NOTE: For easier installation and personal 

safety, it is recommended that two people 

install this product.

IMPORTANT–PLEASE READ CAREFULLY. FOR 

PERSONAL SAFETY, THIS APPLIANCE MUST 

BE PROPERLY GROUNDED TO AVOID SEVERE 

OR FATAL SHOCK.

Insure proper 

ground exists 

before use

The power cord of this 

appliance is equipped 

with a three-prong 

(grounding) plug which 

mates with a standard 

three-prong (grounding) 

wall receptacle to 

minimize the possibility 

of electric shock hazard 

from this appliance.

You should have the wall receptacle and circuit 

checked by a qualified electrician to make sure 

the receptacle is properly grounded.

Where a standard two-prong wall receptacle 

is encountered, it is very important to have 

it replaced with a properly grounded three-

prong wall receptacle, installed by a qualified 

electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT, 

DEFORM OR REMOVE ANY OF THE PRONGS 

FROM THE POWER CORD. DO NOT USE WITH 

AN EXTENSION CORD.

ELECTRICAL 

REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz, 13.5 

amps and 1.58 kilowatts.This product must be 

connected to a supply circuit of the proper voltage 

and frequency. Wire size must conform to the 

requirements of the National Electrical Code or the 

prevailing local code for this kilowatt rating. The 

power supply cord and plug should be brought to a 

separate 15 ampere branch circuit single grounded 

outlet. The outlet box should be located in the 

cabinet above the microwave oven. The outlet box 

and supply circuit should be installed by a qualified 

electrician and conform to the National Electrical 

Code or the prevailing local code.

SMH8165_XAA DE68-03587A-07-EN.indd   3

13/01/2015   17:40:22

Summary of Contents for ME16H702SEB





















Reviews: