background image

Samsung Electronics

7. Easy Sensor Calibration M ethods and Action Points

7-1

1 Place Guide-Roller and Cooking Tray in the Cavity.

2

Put Calibration-Jig on the Tray center.

3

Calibration Button

Press Easy senstor Pow er Level for 2 seconds. 

4

Calibration result(Hexadecimal 4 digits)w ill

be displayed after sensing for 16 seconds.

(* Calibration Jig : IEC 1000cc Beaker

7-1 

Calibration M ethods and Action Points

7-2 

Easy Sensor Voltage Check

Error Code Reason Remarks

E2

Door open or Cancel pad pressed
during Calibration.

Do not open Door/ press Cancel
pad during calibration.

Step Activities

E2

E2

E2

No Pow er.

Replace Defect Components.

Wiring problem for the sensor.

Check w iring.

Sensor PCB damaged.

E3

Repleace Sensor PCB.

Sensor PCB failure.

Repleace Sensor PCB.

M ain PCB failure.

Repleace M ain PCB.

Sensing voltage problem due to 

Replace Sensor PCB.

w rong parts fitted on the PCB.
Low  pow er.

E4

Repleace M agnetron.

EEPROM  Short  or Open on the 
main PCB.

E5

Repleace M ain PCB.

standard load not used during 

Only use standard load.

calibration.

- 0.7 : 1000cc in IEC beaker
- 1.0 : 500cc in normal 600cc beaker

Step Activities

1 Put Inspection - 200cc A cup of w ater on the Tray center.

*  If sensing valeue is less them (or equal) to 15(Hexadecimal), repeat 2~3times from 
   step 1 to step 4 until display show s more than 16(Hexadecimal).
   If you fail to have more than 16(hexadecimal), replace Ass'y Sensor PCB or M agnetron.

   Then;
   -. Leave unit in room temperature about 20 minutes for cooling.
   -. Calibrate Easy Sensor from the beginning step of calibration method.
   -. Check Easy Sensor Voltage again.

4

2

Operate M WO.

3

Press Easy Sensor Clock Button for 2 seconds.

Esay sensor value(Hexadecimal) w ill be displayed.

Voltage Check
Button

Weater 1000cc

Summary of Contents for M1777























































Reviews: