Samsung iPOLIS SRN-1670D User Manual Download Page 11

Page: 11 / 148

English

_11

●

over

view

pArT nAmeS And funCTionS (fronT)

Srn-470d

Srn-1670d

Part Names

Functions

LED Indicator

ALARM

: Lights on when an event occurs.

HDD

: Displays the normal access to HDD.

LED turns on when accessing the hard disk.

NETWORK

: Displays both network connection and data transfer status.

BACKUP

: Displays when Backup is in progress.

REC

: Lights on when recording is in progress.

USB

Connects the USB devices.

OPEN/CLOSE

Used to open and close the DVD-RW disc tray.

Power

Power LED

: Displays the power ON/OFF status.

Power Button

: Used to turn the ON/OFF.

Remote Reception

System

Receive the signal from the remote control.

ALARM

OPEN/CLOSE

HDD

NETWORK BACKUP

REC

USB

SRN - 1670D

DVD RECORDER

NETWORK VIDEO RECORDER

ALARM

OPEN/CLOSE

DVD RECORDER

HDD

NETWORK BACKUP

REC

USB

NETWORK VIDEO RECORDER SRN-1670D

NETWORK VIDEO RECORDER SRN-470D

ALARM

HDD

NETWORK BACKUP

REC

DVD RECORDER

DVD-

USB

d e

Summary of Contents for iPOLIS SRN-1670D





















































































































































Search results

Summary of Contents for iPOLIS SRN-1670D

Reviews:

Related manuals for iPOLIS SRN-1670D

Brands by name

Popular brands

Samsung iPOLIS SRN-1670D, User Manual

Search results

Summary of Contents for iPOLIS SRN-1670D

Reviews:

Related manuals for iPOLIS SRN-1670D

Brands by name

Popular brands