|
26
English
Settings
Support
Remote
Management
When activated, lets Samsung
Call Centre agents diagnose and
fix problems with the product
remotely. Requires an active Internet
connection. Remote Management
service might not be available in
some countries.
Software
Update
For more information about the
Software Update function, see
"Upgrading Software" on page 29.
Usage Mode
Lets you set the Use mode. If you
are using the home cinema at home,
always select Home. Store is for
retail display settings only.
Contact
Samsung
Provides contact information for
assistance with your product.
Reset
Reverts all settings to their defaults
except for the network and Smart
Hub settings, and then starts the
Setup function. Requires that you
enter your security PIN. The default
security PIN is 0000
Networks and the Internet
When you connect this product to a network, you can
use network based applications and functions such as
Smart Hub and BD-LIVE, and upgrade the product's
software through the network connection. For more
information about accessing and using Internet services,
see the Network Services chapter of this manual on
pages 45~53. Instructions for configuring the network
connection start below.
Configuring Your Network Connection
If you didn't configure your network connection during the
initial settings procedure or you need to reset the network
connection, follow the directions below.
Before you begin, contact your Internet Service Provider
to find out if your IP address is static or dynamic. If it
is dynamic, and you have a wired or wireless network,
we recommend using the Automatic configuration
procedures described below.
If you are connecting to a wired network, connect the
product to your router using a LAN cable before you start
the configuration procedure.
To begin configuring your network connection, follow
these steps:
1.
In the Home screen, select
Settings
, and then
press the
E
button.
2.
Select
Network
, and then press the
E
button.
3.
Select
Network Settings
, and then press the
E
button.
4.
Go to the instructions for Wired networks starting
below or the instructions for Wireless networks
starting on page 27.
Wired Network
Wired – Automatic
After following Steps 1 to 3 above:
1.
In the Network Settings screen, change
Network
type
to
Wired
. Then, select
Connect
and press
the
E
button. The product detects the wired
connection, verifies the network connection and
then connects to the network.
2.
When it is done, highlight
OK
, and then press
E
button.
Wired - Manual
If you have a static IP address or the automatic procedure
does not work, you'll need to set the Network Settings
values manually.
After following Steps 1 to 3 above:
1.
In the Network Settings screen, change
Network
type
to
Wired
. Then, select
Connect
and press the
E
button.
The product searches for a network, and then
displays the connection failed message.
| NOTES |
If it is possible to connect the home cinema to your
network wirelessly, select
Change Network
at this
point, change the
Network type
to
Wireless
, and
then go to the instructions for wireless networks on
page 27.
Network Settings
Wired network connection failed.
MAC Address
XX:XX:XX:XX:XX:XX
IP Address
0. 0. 0. 0
Subnet Mask
0. 0. 0. 0
Gateway
0. 0. 0. 0
DNS Server
0. 0. 0. 0
Unable to connect to the network. Try the following: check if your IP address is
set correctly in IP Settings. Contact your Internet service provider for more
information.
IP Settings
Change Network
Retry
Close
2.
Use the ◄► buttons to select
IP Settings
, and
then press the
E
button. The IP Settings screen
appears.
HT-F6500_30W_50W-XU_0207.indd 26
HT-F6500_30W_50W-XU_0207.indd 26
2013-02-07 오후 7:36:22
2013-02-07 오후 7:36:22
