manualshive.com logo in svg

Samsung GT-E2652, Service Manual, Page: 23 / 73

Share
Download
Samsung GT-E2652 Service Manual Download Page 23

SAMSUNG Proprietary-Contents may change without notice

7. Level 2 Repair

7-2

This Document can not be used without Samsung's authorization

1) Separate LCD and KEYPAD from the

FRONT CASE.

※

Caution

1) Be care of scratch and molding damage.
2) Be care of damage to the LCD.

1) Unscrew the 2 points.

※

Caution

1) Be care of scratch and PBA damage.
2) Torque : 1.0 ~ 1.2 Kgf·cm

1) Separate the INTENNA, SHIELD CAN from the

PBA ASS'Y.

（

Caution

1) Be care of scratch and PBA damage.

1) Separate the MOTOR from the DUAL SOCKET

BRACKET.

1) Separate the DUAL SOCKET CONNECTOR &

CAMERA MODULE from the PBA ASS'Y.

（

Caution

1) Be care of CAMERA SOCKET damage & CAMERA MODUL
E scratch.

5

1) Separate LCD and KEYPAD from the FRONT
CASE.

6

1) Unscrew the 2 points.

7

1) Separate the INTENNA, SHIELD CAN from the

PBA ASS'Y.

8

1) Separate the MOTOR from the DUAL SOCKET

BRACKET.

1) Separate the DUAL SOCKET CONNECTOR &

CAMERA MODULE from the PBA ASS'Y.

Summary of Contents for GT-E2652










































































Reviews:

No comments