Samsung F22T45 Series User Manual Download

Page: 27 / 40

System

2nd

3rd

Description

FreeSync

technology is solution that eliminates screen tearing without all the usual lag and latency.

FreeSync

can be operated when you use

AMD's graphic card with supporting

FreeSync

solution.

For more information, see

FreeSync

page.

Volume

Change the

Volume

setting.

Eco Saving Plus

Reduce energy consumption compared to consumption at the maximum brightness level.

•

Off

: Deactivate the

Eco Saving Plus

function.

•

Auto

: The power consumption will automatically be reduced by about 10% over the current setting.

(The reduction of power consumption depends on the customer screen brightness condition.)

•

Low

: Saves up to 25 % energy compared to the maximum brightness.

•

High

: Saves up to 50 % energy compared to the maximum brightness.

―

This option is not available when

Picture Mode

is in

Dynamic Contrast

mode.

―

This menu is not available when

Game Mode

is enabled.

―

This menu is not available when

Eye Saver Mode

is enabled.

Dynamic Brightness

Automatically adjust the Brightness to provide the best possible screen contrast under the current conditions.

Summary of Contents for F22T45 Series









































Search results

Summary of Contents for F22T45 Series

Reviews:

Related manuals for F22T45 Series

Brands by name

Popular brands

Samsung F22T45 Series, User Manual

Search results

Summary of Contents for F22T45 Series

Reviews:

Related manuals for F22T45 Series

Brands by name

Popular brands