Samsung DP15HS Service Manual Download

Page: 16 / 73

PROCEDURE

For trained and experienced service technicians
only.

Use the following procedure to correct minor
color purity problems:

1. Make sure the display is not affected by

external magnetic fields.

2. Very carefully break the glue seal between the

2-pole purity convergence magnets (PCM), the
band and the spacer (see Figures 4-12).

3. Make sure the spacing between the PCM

assembly and the CRT stem is 29 mm ± 1 mm.

4. Display a green pattern over the entire display

area.

5. Adjust the purity magnet rings on the PCM

assembly to display a pure green pattern.
(Optimum setting: x = 0.295 ± 0.015,
y = 0.594 ± 0.015)

6. Repeat steps 4 and 5 using a red pattern and

then again, using a blue pattern.

Table 4-4. Color Purity Tolerances

(For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02)

7. When you have the PCMs properly adjusted,

carefully glue them together to prevent their
movement during shipping.

4 Alignment and Adjustments

4-8

DP15H*/DP17L*

Red:

x = 0.640 ± 0.015

y = 0.323 ± 0.015

Green:

x = 0.295 ± 0.015

y = 0.594 ± 0.015

Blue:

x = 0.142 ± 0.015

y = 0.066 ± 0.015

Summary of Contents for DP15HS










































































Search results

Summary of Contents for DP15HS

Reviews:

Related manuals for DP15HS

Brands by name

Popular brands

Samsung DP15HS, Service Manual

Search results

Summary of Contents for DP15HS

Reviews:

Related manuals for DP15HS

Brands by name

Popular brands