manualshive.com logo in svg

Samsung CXJ1352AX, Service Manual, Page: 9 / 100

Share
Download
Samsung CXJ1352AX Service Manual Download Page 9

Alignments and Adjustments (VCR)

Samsung Electronics

3-1

3-1 Mechanical Adjustments

3. Alignments and Adjustments (VCR)

3-1-1 Tape Transport  Adjustment

Note : The tape transport system was adjusted precisely in the factory, any adjustments is 

unnecessary except for:

✦

Noise on the screen.

✦

Tape damage.

✦

Parts replacement in the tape transport system.

3-1-1(A) PARTS LOCATIONS

The lower flange height of tape guide is used as the reference height for the transport adjustment.  To
maintain the height of the tape guide, do not apply excessive force onto the main base.

CYLINDER ASS'Y

TAKE UP REEL DISK

#8 GUIDE POST

#9 GUIDE POST

SUPPLY REEL DISK

CAPSTAN

PINCH ROLLER

GUIDE ROLLER "T"

GUIDE ROLLER "S"

FULL ERASE HEAD

#3 GUIDE POST

TENSION POST

HEIGHT SCREW

TILT SCREW

X - POSITION
ADJUST SILT

AZIMUTH SCREW

Fig. 3-1 Parts Locations of transport system

Fig. 3-2 Vertical section of tape transport system

POST TENSION

MAIN BASE

FE HEAD

CYLINDER ASS'Y

PINCH ROLLER

GUIDE ROLLER "S"

GUIDE ROLLER "T"

#8 GUIDE POST

#9 GUIDE POST

CAPSTAN SHAFT

ACE HEAD

#3 GUIDE POST

Summary of Contents for CXJ1352AX





































































































Reviews:

No comments