Samsung BD-H8500A Service Manual Download Page 8

Page: 8 / 82

1. Precautions

1.4. Installation Precautions

1) Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock.

2) Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature

may cause fire.

3) Make sure to turn the power off and unplug the power cord from the outlet before repositioning the product. Also check

the external connectors if they are fully unplugged. Damage to the cord may cause fire or electric shock.

4) When installing the product, leave enough space (0.4m) between the product and the wall for ventilation purposes. A

rise in temperature within the product may cause fire.

5) If an equipment is provided with a replaceable battery, and if replacement by an incorrect type could result in an

explosion (for example, with some lithium batteries), the following applies:

CAUTION

• Risk of explosion if battery is replaced by an incorrect type dispose of used batteries according to the instructions.

• Do not dispose of batteries in a fire.

• Do not short circuit, disassemble or overheat the batteries.

• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• Do not be exposed to excessive heat such as sunshine, fire or the like.

1-5

Summary of Contents for BD-H8500A


























Search results

Summary of Contents for BD-H8500A

Reviews:

Related manuals for BD-H8500A

Brands by name

Popular brands

Samsung BD-H8500A, Service Manual

Search results

Summary of Contents for BD-H8500A

Reviews:

Related manuals for BD-H8500A

Brands by name

Popular brands