Samsung AM040FXMDEH Installation Manual Download Page 61

Page: 61 / 66

Error code

Please follow below instruction when there is error on sensor.

Check the resistance of the sensor

- Hydro unit : Water pipe inlet/outlet, R-410A EVA IN/OUT

10 kΩ @ 25 °C

- Hydro unit HT : Water pipe inlet/outlet

200 kΩ @25 °C, R-410A EVA IN/OUT

10 kΩ @25 °C

Check the DVM Hydro unit / Hydro unit HT's system diagram for the location of each sensor.

Check if the sensor is attached properly to the copper pipe.

If the problem persist after checking following above instruction, replace the PBA.

When error is occurred due to 'Freeze prevention', 'Pipe rupture protection' (E907, E908/E909), make sure to solve
the cause before re-start the operation.

CAUTION

Display

Explanation

Communication error between DVM Hydro unit / Hydro unit HT and outdoor unit

(When DVM Hydro unit / Hydro unit HT is having trouble with receiving data from outdoor unit)

Communication error on outdoor unit

(When outdoor unit is having trouble sending data to DVM Hydro unit / Hydro unit HT)

Communication error between DVM Hydro unit / Hydro unit HT and Control Kit (Detection from the Control Kit)

Error on room temperature sensor of DVM Hydro unit / Hydro unit HT (Short or Open)

Error on EVA IN sensor of DVM Hydro unit / Hydro unit HT (Short or Open)

Error on EVA OUT sensor of DVM Hydro unit / Hydro unit HT (Short or Open)

EVA IN sensor of DVM Hydro unit / Hydro unit HT is detached

EVA OUT sensor of DVM Hydro unit / Hydro unit HT is detached

EVA IN and EVA OUT sensor of DVM Hydro unit / Hydro unit HT is detached

Error due to opened EEV of DVM Hydro unit / Hydro unit HT (2nd detection)

Error due to closed EEV of DVM Hydro unit / Hydro unit HT (2nd detection)

Mixed operation mode error

EEPROM error

EEPROM option setting error

Check the water circulating

Cross wiring error (When power line is connected to communication line of DVM Hydro unit / Hydro unit HT)

Error due to disconnected Thermal Fuse (When the temperature of terminal block is increases)

Communication error between remote controller and the DVM Hydro unit / Hydro unit HT

Communication error between master and slave remote controller

Tracking error between remote controller and the DVM Hydro unit / Hydro unit HT

Error due to exceeding maximum numbers of Hydro unit installation (16 units)

Error due to exceeding maximum numbers of wired remote controller installation (2 units)

Error caused by installing mixed models

Remote controller's temperature sensor is disconnected or has problem

Data error on remote controller (Memory read/write error)

k}tGokyvGo{ptXYWZ`]]hTXluUGGG]W

YWXZTW_TW]GGG㝘㤸G`a[[a\Z

Summary of Contents for AM040FXMDEH



































































Search results

Summary of Contents for AM040FXMDEH

Reviews:

Related manuals for AM040FXMDEH

Brands by name

Popular brands

Samsung AM040FXMDEH, Installation Manual

Search results

Summary of Contents for AM040FXMDEH

Reviews:

Related manuals for AM040FXMDEH

Brands by name

Popular brands